Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Stopping app_timer (using app_timer_stop) results in too much current during ON,IDLE mode 0

I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following: Initializes the app_timer using the scheduler: ...

1534 views

0 replies

Started over 11 years ago
by Kyle
Not Answered

Control GPIO by PPI and timer1 +1

I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000. I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...

1887 views

0 replies

Started over 11 years ago
by mansfield
Not Answered

One command execution time on serialization 0

Hi, I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...

757 views

0 replies

Started over 11 years ago
by Elliot.Chao
Not Answered

Has anybody used pervasive dispalay (repaper) on NRF51822 Evaluation Kit? 0

Has anybody got it working? I ported the EPD library from Adruino EPD libray but not sure where its going wrong.

767 views

0 replies

Started over 11 years ago
by Barada Mishra
Not Answered

get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE 0

I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...

2479 views

0 replies

Started over 11 years ago
by julian

Recent in Nordic blog

micro:bit v2 Pager

Ali Aljaani

In this blog post, we will show you how to build a pager with a micro:bit v2 and nRF Connect SDK. Writing application in C using nRF Connect SDK gives you the highest level of control over the micro:bit…
- 8 Apr 2022
Comparing range with Bluetooth Low Energy of the nRF21540 DK and the nRF52840 DK

Susheel Nuguru

FYI: The video above shows a similar test as this blog post, just using two nRF52840 DKs and two nRF21540 DKs. The blog post uses one nRF52840 DK and two nRF21540 DKs. One of the reasons we did multiple…
- 7 Apr 2022
nRF Cloud REST API and configuring the Asset Tracker v2 application

Mariano Goluboff

Introduction The Asset Tracker v2 is a highly configurable asset tracker application available in nRF Connect SDK, that supports, among many things, multiple cloud services and configuring the behavior…
- 22 Mar 2022

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020