Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
test post 0

This is a test post
452 views

0 replies

Started over 5 years ago
by [email protected]
Not Answered
Anyone able to pair using the pc-ble-driver 0

I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
503 views

0 replies

Started over 5 years ago
by brianreinhold
Not Answered
New profile vs. NUS +1

Hi, I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central. The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
527 views

0 replies

Started over 5 years ago
by ran
Not Answered
Dependability competition based on nRF52840 0

The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
395 views

0 replies

Started over 5 years ago
by calbo
Not Answered
Nodic CSCS example 0

Hi, I find the CSCS example program reading zero at low cadence levels below around 50 rpm. Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
590 views

0 replies

Started over 5 years ago
by TonyM

Recent in Nordic blog

nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015
Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019