Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF9161 SIM LTE connectivity issue 0

Hello, We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
13 views

0 replies

Started 3 hours ago
by sposelenov
Not Answered
handle nrf_libuarte_async_evt_t in thread mode 0

Hello, I'm using nRF5 SDK v17.1.0. I couldn't find anything about it. Could I ran in some problems if i choose to handle the nrf_libuarte_async_evt_t in thread mode and...
20 views

0 replies

Started 3 hours ago
by jul-nc
Not Answered
Build for custom board converted to 2.8 format getting error "list GET given empty list" in CMakeLists.txt splitting BOARD_QUALIFIERS 0

We have a custom board that I ran through the board_v1_to_v2.py program and then attempted to build under SDK and Toolchain 2.8. When I run it it failed in the CMakeLists...
15 views

0 replies

Started 3 hours ago
by robbsadler
Not Answered
Weak Pin Drive Strength on nRF5340 DK Leading to SPI Communication Failure with ICM-42688-P 0

I am using the Nordic nRF5340 DK to communicate with the ICM-42688-P sensor via SPI. However, the sensor does not respond to the MCU's commands. After observing the SPI clock...
- nRF Connect SDK
- Evaluation
- spi
- hardware
- nRF5340
19 views

0 replies

Started 4 hours ago
by MatryoshkaLJY
Not Answered
PPK2-PowerSwitch SW1 0

Hello, I'm just starting with the Power Profile Kit 2. I've read all available documentation but I didn't find any information about the switch SW1 called 'POWER'. There...
16 views

0 replies

Started 4 hours ago
by HBehr

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Peripherals And RF Test: Writing device drivers for UART peripherals

Halvor Bjorstad

This post aims to cover some of the specifics of developing device drivers for UART peripherals for Zephyr.
- 20 Jul 2021
Software: Testing concurrent multi-protocol support of Zigbee & BLE over single USB connection to external CPU

Mark Q

Purpose The purpose of this blog is to showcase how a single USB bus can be used as the physical transport for multiple protocols when an external CPU is the controller. Specifications as tested Boards…
- 13 Jul 2021
Peripherals And RF Test: Working around missing shield labels (on the nRF9160 DK)

Embla Flatlandsmo

Table of Contents Objectives What are device tree overlays, and how do they relate to shields? Why are Arduino nodes not recognized in the nRF9160 DK? The workaround: Using the shield as a board ove…
- 25 Jun 2021
Peripherals And RF Test: LVGL on a TFT LCD Display with the nRF9160 DK

Embla Flatlandsmo

Table of Contents Hardware Components Wiring Software Prerequisites Steps Incorporating this into other projects Further reading Attached files This blog post demonstrates how to get a LVGL sample…
- 25 Jun 2021
Software: Using the NCS / West to program the Radio_Test example into the nRF5340-DK for agency testing.

Jay Tyzzer

Background: There is a need to be able to put a Nordic Semiconductors S0C /transceivers into modes where the physical layer and RF characteristics may be ascertained. The radio test example is used to…
- 18 Jun 2021
Software: Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice - Part 2 Central role

Hung Bui

This is part 2 of the series Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice based Bluetooth applications You can find the other parts here: Part 1 - Peripheral Role. Part…
- 5 May 2021