Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Writing to flash memory 0

Hi, I'm using an nRF52810 on a custom board and I'm using softdevice s112_nrf52_7.2.0_softdevice.hex. I want to write some information (just 4 bytes) to flash memory,...
- development
- software
- flash
- nrf52810
15 views

0 replies

Started 6 hours ago
by Kenneth_CBS
Not Answered
Unable to configure nRF Sniffer for 802.15.4 for ZigBee 0

Hello All, I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup, https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
13 views

0 replies

Started 6 hours ago
by UVP
Not Answered
Can't open syscall/gpio.h 0

Hi everyone, I am getting this build error while I am trying to call a function from gpio.h in my custom code Looking at my includes I see this This is a really...
15 views

0 replies

Started 6 hours ago
by ReginaA101
Not Answered
Timeout exit from the boot loader 0

I am developing an application that uses NCS2.8.0. For FW updates, the nRF52833 USB ACM bootloader is enabled. However, there are some problem. My device has a battery...
15 views

0 replies

Started 7 hours ago
by DX_HK
Not Answered
nrf52840-read data 0

Hello forum , In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
21 views

0 replies

Started 7 hours ago
by pushparaj

Recent in Nordic blog

Step by Step Guide to Setup and Start Developing with the nRF51 DK and Keil

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, get the tools installed and get the software (SW) development environment…
- 17 Jun 2015
Debugging using QtCreator on Mac

wim

This post started as a question, but got the suggestion to post this as a blog post. Here it is. I have been trying to get QtCreator configured such that I can use it as my IDE for the nrf51822 on Mac…
- 12 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Raspberry Pi 2

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015

Latest guides

nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019
Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019