Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nPM1300 pin connections when BUCK2 not used 0

I'm looking at Product Specification v1.2 - Reference Circuitry Configuration 2 where BUCK2 is not used. The schematic shows the output VOUT2 is tied to VSYS in this case...
18 views

0 replies

Started 21 hours ago
by Nick_RA
Not Answered
BLE Connection Issue with Multiple Simultaneous Peripherals 0

I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
30 views

0 replies

Started 22 hours ago
by Arthur J Sary
Not Answered
Optimizing Power Consumption for Battery-Operated Matter-over-Thread Device (nRF54L15) 0

Hi Nordic Team, I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
- software
- battery
- Evaluation
- nRF54L15
- thread
35 views

0 replies

Started 22 hours ago
by Bhavya Mathukiya
Not Answered
Problem with GNSS - delay in detecting satellites 0

Hello, i'm having a problem with the satellite detection time when I start gnss search. When I start the search, for a while at first the satellites are not detected and then...
42 views

0 replies

Started 22 hours ago
by GoncaloS
Not Answered
BLE Mesh Deep Sleep and RTC Setup 0

Hi, I am using Mesh of 30 nodes with avg Current Consumption 6mA and 2mA in sleep mode(by calling k_sleeps) , timer is 1s timer is running to keep Real Time incremented...
35 views

0 replies

Started 1 day ago
by AP

Recent in Nordic blog

6LoWPAN for Bluetooth low energy on OpenWRT

Glenn Ruben Bakke

OpenWRT is one of the most popular open source Linux-based router firmware alternatives for commodity routers. From kernel 3.17, Linux has supported 6LoWPAN for Bluetooth low energy (BLE) through the…
- 13 Mar 2015
IPv6-Brewed Coffee Over Bluetooth Smart

Glenn Ruben Bakke

Believe it or not, the day has come when your coffee machine could know what exactly what kind of coffee you like to drink depending on the cup you’re using, the time of day, and a multitude of other…
- 4 Mar 2015
Debugging Arduino project with Atmel Studio

Stefan Birnir Sverrisson

When using nRF8001 with an Arduino board, Atmel Studio is a good free tool to use for development of your firmware. The following video shows a procedure in Atmel Studio in order to enable debugging of…
- 19 Feb 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019