Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
ble_radio_notification_init invoke failed 0

We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay. My question...
- ble_radio_notification_init
830 views

0 replies

Started over 8 years ago
by Jiming
Not Answered

[Solved] SPI: Not getting SCK signal 0

Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong. Hi guys, at the...

1447 views

0 replies

Started over 8 years ago
by uC_newbie
Not Answered

Looking for a developer in Denmark 0

Hi Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...

509 views

0 replies

Started over 8 years ago
by Martin
Not Answered

One RX and Three TX system with NRF24L01+ 0

This system does not work if I enable the third Pipe (Pipe2) . The system is working without any problem as one RX and two TX (Pipe0 and Pipe1). The problem on enabling...

556 views

0 replies

Started over 8 years ago
by Erol
Not Answered
sd_flash_write inside BLE event 0

Hello, i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method. What i would like to do is to write to flash from...
- sd_flash_write
- event
- ble
- flash
- nrf52832
1013 views

0 replies

Started over 8 years ago
by schef

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019