Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Unable to configure nRF Sniffer for 802.15.4 for ZigBee 0

Hello All, I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup, https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
13 views

0 replies

Started 12 hours ago
by UVP
Not Answered
Can't open syscall/gpio.h 0

Hi everyone, I am getting this build error while I am trying to call a function from gpio.h in my custom code Looking at my includes I see this This is a really...
15 views

0 replies

Started 12 hours ago
by ReginaA101
Not Answered
Timeout exit from the boot loader 0

I am developing an application that uses NCS2.8.0. For FW updates, the nRF52833 USB ACM bootloader is enabled. However, there are some problem. My device has a battery...
15 views

0 replies

Started 12 hours ago
by DX_HK
Not Answered
nrf52840-read data 0

Hello forum , In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
22 views

0 replies

Started 12 hours ago
by pushparaj
Not Answered
How to use custom board revisions in application code? 0

Hi, I use Nordic connect SDK and have to create a new revision for a custom board, because there are some hardware changes. I managed to create an overlay for the new revision...
22 views

0 replies

Started 15 hours ago
by ilockit_CFR

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Getting Started : Getting started with Bluetooth Electronic Shelf Labels (ESL) and Periodic Advertising with Responses (PAwR)

Lorenzo Amicucci

The new Bluetooth 5.4 features Periodic Advertising with Responses (PAwR) and Encrypted Advertising Data (EAD) can be used for one-to-many applications. One of these is the Electronic Shelf Labels (ESL…
- 7 Aug 2024
nRF5x: General PCB design guidelines for nRF52 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Nov 2023
Software: Periodic Advertising with Responses (PAwR): A practical guide

Hung Bui

Periodic Advertising with Responses (PAWR) is a new feature in Bluetooth 5.4. It extends the periodic advertising protocol from Bluetooth 5.0. Periodic advertising, where a device sends broadcast data with…
- 13 Sep 2023
nRF5x: General PCB design guidelines for nRF53 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Jul 2023
Software and Protocols: nRF Cloud Access Provisioning

Charlie

Please note that some information on this page may be outdated due to ongoing improvements in nRF Cloud. For the most current details on provisioning services, refer to the nRF Cloud Security Services…
- 1 Dec 2022
Software and Protocols: Field verification of GNSS on the nRF91 Series

JaniM

Introduction The intention of this guide is to clarify and describe the main aspects relevant to the GNSS receiver functionality on the nRF9160 as well as build configurations, tool recommendations and…
- 10 Jun 2022