Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF54L15 CAAA WLCSP 300 μm pitch matching network components 0

Hi, We have a pretty small device to be designed and I was wondering if nRF54L15 CAAA WLCSP would have updated recommendations for matching network components available...
21 views

0 replies

Started 2 days ago
by PenttiVaan
Not Answered
Multi image project as Zephyr module 0

Hello, I've been working with nRF9160 for a while now and wanted to let you know, I love this little piece of hardware. The possibilities, the small form factor, the power...
- development
- software
- nRF9160
- Feature
- dfu
29 views

0 replies

Started 2 days ago
by a_ku
Not Answered
NRF52840　About the 32.768kHz crystal oscillator　(LFXO) 0

Is the GPIO pin in a reset state until the start-up time of the 32.768kHz crystal oscillator?
32 views

0 replies

Started 2 days ago
by Kono Kohei
Not Answered
nRF Connect(Android, latest Version) 0

I have problems with nRF Connect(Android, latest Version, no version number found) to find BLE devices with 2M phy, coded phy and extended advertising. So i am running nRF...
20 views

0 replies

Started 2 days ago
by karlheinz
Not Answered
nRF9160 to nRF9151 hardware migration 0

Dear Nordic Team, I hope this message finds you well. Some time ago, we asked about the migration from nRF9160 to nRF9161. We want to ask the same question regarding...
19 views

0 replies

Started 2 days ago
by mjaszczykowski

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019