Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF52840 I2S write failed -11 0

Hello, I am using two nrf52840 DKs to test ble transmission and i2s output. The nRF Connect SDK I use is v2.6.0. Both of them are ble connected. One sends data to the...
4 views

0 replies

Started a few seconds ago
by LandyWang
Not Answered
How does the Online Power Profiler for Wi-Fi tool calculate energy consumption 0

How does the Online Power Profiler for Wi-Fi tool calculate energy consumption, and is there a formula or document explaining its energy consumption calculation principle...
4 views

0 replies

Started 9 minutes ago
by ChengQing Zhao
Not Answered
In Nrf7002dk facing issue with TWT Powersave Mechanism 0

Hi, 1. I was facing issue with my nordic device saying [02:16:46.206,481] <err> net_pkt: Data buffer (1328) allocation failed. [02:16:46.206,481] <wrn> net_conn: pkt...
6 views

0 replies

Started 24 minutes ago
by Jaswanth Rajigiri
Not Answered
How to change the Link request interval of OpenThread in NCS 0

As shown in the figure above, if I need to modify the time interval of OpenThread's Link request or parent request, how can I do it? Thank you NCS 2.6.0 NRF52840
8 views

0 replies

Started 40 minutes ago
by Quay
Not Answered
Why does it take so long for nRF9151DK to register on NB network? 0

I am developing a product for a customer using NRF9151(ncs2.7.0, modem fw: mfw_nrf91x1_2.0.2). While verifying it on the DK board, I discovered an issue. When the system starts...
- development
- software
- nb-iot
- nRF9151
- C
10 views

0 replies

Started 49 minutes ago
by duxinglang

Recent in Nordic blog

New Command Line Interface and enhanced Logger - part 2.

Krzysztof Chruscinski

If you haven't yet get to know command line interface (nrf_cli) module significantly improved in nRF5 SDK 14.0.0 please check this blog post: New command line interface - part 1 Enhanced logger and…
- 22 Aug 2017
MultiLink with Peripherals & Centrals in the nRF5 SDK v13

JustinLee

##Introducing concurrent MultiLinks I’d like to inform that it is possible to configure concurrent-multiple connections with several Centrals and Peripherals. This behavior can be possible to use examples…
- 22 Aug 2017
Nordic Thingy:52 Raspberry Pi Python Interface

gamnes

Thingy:52 Python Raspberry Pi Interface This blog is a follow up to both the Nordic Thingy:52 node.js/Raspberry Pi demos and the https://devzone.nordicsemi.com/blogs/1160/walkthrough-of-nordic-thingy52…
- 18 Aug 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019