NRF52840 System ON Low Power almost reached but 1µA comes from nowhere.

[icedfluid]

Hi dear forumers,

 

I'm in the goal of achieving lowest current consumption on my PCA10056 DK board, with an nrf52840.

I converted a previous zephyr firmware who perfectly runs low current on PCA10040 to the PCA10056 board but it resulted with an abnormal current consumption.

The target with the nrf52840 is 2.35µA and I'm seeing 3.5µA.

1) To troubleshoot, I decided to build a new project from scratch using the simplest zephyr code and SDK 2.6.1. I disabled every possible peripheral in the device tree overlay.

Correctly cut the SB40 jumper on the board and measure with the PPK2 in ampmeter, and I still saw ... ~3.5µA.

Code Zephyr

prj.conf

measure

 

2) Then I applied a software SYSTEM OFF (NRF_POWER->SYSTEMOFF = 1) just to be sure, and I measure 1.5µA, which is incorrect and should be ~0.5µA.

 

3) Thinking that my board might have a ~1µA leak, I decided to flash a firmware from a fellow developer on this forum (here 538705.zephyr.hex),  To my surprise, the current consumption dropped to 2.3µA between BLE advertising ! 
This indicated that my board doesn't have a leak and my measurements are correct.

So, the question is, why can't I achieve the same results as "ujur007" with my simple firmware?

Could it be the Zephyr version (v3.5.99-ncs1-1) ? The SDK version ?  Because This is clearly a software issue.

Here my HEX : 6165.zephyr_brotechnic.hex


Best regards.
Vincent
 

[Simonr]

Hi Vincent

Sorry about the late reply to this ticket. Most likely, the reason you're seeing ~3.5µA here is because there is some minor leakage when measuring power on the nRF52840 DK so getting all the way down to the optimal current consumption on a large DK won't be possible. It will vary a bit from device to device, but it's rare to see a DK be able to go lower than 3µA. You can also check out this blog post explaining how to optimize power consumption on nRF52 designs.

Best regards,

Simon

[icedfluid]

Hi Simon,
Thanks for the response.

But, as I explained, there's no leakage on the board since the correct current consumption is achieved with this hex found on this thread.
I see a perfectly conform to specs : 2.35µA.
And at the moment I switch to my hex, current climbs to ~3.5µA. 

Regards,

Vincent

[Simonr]

Hi again Vincent

Sorry, I missed that when reading through this yesterday. Can you explain what exactly your .hex is doing. For example, is some RAM blocks retained, or do you have an RTC running to track time of something perhaps.

Best regards,

Simon

[icedfluid]

Hi Simon,

I made a simple Zephyr program that goes idle with full RAM retention and RTC (for Zephyr ticker) and no peripherals. We should be at 2.35µA :

When I use this HEX I see 2.20µA between advertising : 

When I use my program I see 3.45µA : 

Here, you can find the public git with the full code :
https://gitlab.com/vinkerozen/nrf52840-power-consumption/-/tree/nrf52840?ref_type=heads

Regards,
Vincent

[Simonr]

Okay, could it be that your hex does not enable the DCDC converter maybe? See this ticket for reference on how to do that:  How to enable DCDC regulator in nRF Connect SDK (NCS) 

Best regards,

SImon 

[icedfluid]

Hi Simon, 

The DCDC is enabled by default by the SDK or I miss something ? 

That's the def Konfig of the board :


Regards,
Vincent

[icedfluid]

I also try this way with no luck :