• State Not Answered
  • Replies 63 replies
  • Subscribers 75 subscribers
  • Views 15634 views
  • Users 0 members are here
Attachments (3) Download All
Nordic Case Info
  • Case ID: 252243
Options
This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts

Thread Border Router networking fail

Rick

Hello Nordic Taam:

I follow the WEB steps below

https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v4.1.0%2Fthread_ot_performance_measurement.html

Software Development Kit > nRF5 SDK for Thread and Zigbee v4.1.0 > Thread > Thread tools > Thread Border Router

nRF52840 DK Version：nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\ncp\ftd\uart\hex

Raspberry Pi 3 Version：RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha

Use nRF52840 DK UART connect Raspberry Pi 3 to get the following information

wpan0 => [
"NCP:State" => "associating"
"Daemon:Enabled" => true
"NCP:Version" => "OPENTHREAD/20191113-00534-gc6a258e3; NRF52840; Apr 5 2020 21:51:18"
"Daemon:Version" => "0.08.00d (; Apr 21 2020 19:11:43)"
"Config:NCP:DriverName" => "spinel"
"NCP:HardwareAddress" => [F4CE363EC3C45B0E]
]


pi@raspberrypi:~ $ sudo wpanctl status
wpan0 => [
"NCP:State" => "uninitialized"
"Daemon:Enabled" => true
"NCP:Version" => ""
"Daemon:Version" => "0.08.00d (; Apr 21 2020 19:11:43)"
"Config:NCP:DriverName" => "spinel"
"NCP:HardwareAddress" => [F4CE363EC3C45B0E]
]

If I have the wrong steps or have not completed, please give me some pointers, thank you.

Also, can you teach me how to set up the Thread Border Router successfully on Raspberry Pi 3?

Best Regards

Rick.

Parents
  • 0

    Hi,

    The instructions on Thread Border Router is the latest and should be correct. It also looks like you are using the correct versions of the firmware and border router image. 

    I have tested this multiple times before, and have not had any issues with getting the network up and running.

    Are you using a revision 1 DK or later? Did you have the DK connected to the RPi before you booted it? Did you run 'erase all' command on the DK before flashing the NCP FW? You did not run any other commands on the border router prior to the "sudo wpanctl status" command?

    If nothing works, I would suggest that you start over and flash the DK and border router image again to the devices to see if that solves any issues.

    Best regards,
    Jørgen

  • 0 in reply to Jørgen Holmefjord

    Hi Jørgen:

    How are you today!

    Is there any update?

    Pls kindly help advise how to solve it?

    Best Regards,

    Rick.

  • 0 in reply to Jørgen Holmefjord

    Hi Jørgen,


    1. I did not use the publish of two devices.
    I use this example "Thread MQTT-SN Example".
    Use one device of the MQTT-SN Subscriber application and other one device of the MQTT-SN Publisher application. (one publish device, one subscribe device)

    2. Yes, two subscribers well the same problems too. do you have any advice that can solve the problems of two subscribers?

    3. Now I have two devices, wanted to combine operations publish and subscribe at the same time in the device.
    Pls kindly help advise how to solve it?

    Best Regards,

    Rick.

  • 0 in reply to Rick

    Hi Rick,

    Your latest questions is getting far outside of the topic of this thread. Can you please post it in a new thread, to prevent this from getting too messy? That will help other users with similar questions find the information much more easily.

    If you do that, we will try to help you achieve what you want.

    Best regards,
    Jørgen

  • 0 in reply to Jørgen Holmefjord

    Hi Jørgen:

    I created a new thread is Thread MQTT-SN Example publish and subscribe can not combine operations ,

    Pls kindly help advise how to solve it?

    Best Regards,

    Rick.

  • 0 in reply to Jørgen Holmefjord

    Hi Jørgen:

    Now I have support IPv6 from ISP and Router is (ASUS RT-AX56U)，but I still not get /62 prefix.

    this is my ifconfig from RPi .

    pi@raspberrypi:~ $ ifconfig eth0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500

        inet 192.168.50.103  netmask 255.255.255.0  broadcast 192.168.50.255

        inet6 2001:b030:214e:2200:****:****:****:****  prefixlen 64  scopeid 0x0<global>

        inet6 fe80::ba27:ebff:feda:4146  prefixlen 64  scopeid 0x20<link>

        ether b8:27:eb:da:41:46  txqueuelen 1000  (Ethernet)

        RX packets 870  bytes 76151 (74.3 KiB)

        RX errors 0  dropped 0  overruns 0  frame 0

        TX packets 530  bytes 78362 (76.5 KiB)

        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

    and the WEB steps description, How can I setting DHCPv6 service for Rpi and disable autoconfig?

    When dealing with the native IPv6 connectivity, make sure you use the DHCPv6 service and not the popular Stateless Address Autoconfiguration (SLAAC) tool. This autoconfig tool will only provide a 64-bit long prefix that is not sufficient to delegate a new 64-bit long prefix for the Thread network.

    Best Regards,

    Rick.

  • 0 in reply to Rick

    Hi,

    I do not have this router available, so unfortunately I'm not able to help you with configuration of this. You should contact the manufacturer of the router (Asus) to get help on configuration and details about whether this router can support larger address spaces. I have only been able to get this to work with a router running OpenWRT firmware, but I have not tested on a large number of devices..

    Best regards,
    Jørgen

Reply
  • 0 in reply to Rick

    Hi,

    I do not have this router available, so unfortunately I'm not able to help you with configuration of this. You should contact the manufacturer of the router (Asus) to get help on configuration and details about whether this router can support larger address spaces. I have only been able to get this to work with a router running OpenWRT firmware, but I have not tested on a large number of devices..

    Best regards,
    Jørgen

Children
Related
Terms of service