Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
I'm using SDK v11, nRF51
I started developing with S130, v2.0.1
The device is peripheral only, so I decided to switch to S110 v8.0.0, since I need the memory.
I made...
I don't have a particular issue right now, just a concern that I have because my device needs to be bulletproof when it comes to reset behavior.
When sd_mbr_command(SD_MBR_COMMAND_INIT_SD...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
Hello,
I'm developing nRF52 with Keil5.14.
Before I used nRF52_SDK_0.9.2 and it worked fine.(With NordicSemiconductor.nRF_DeviceFamilyPack.8.0.3.pack)
I upgrade the...
Hi all
According to the following post, the RAMONB register doesn't exist since the nRF51822 has only 2 RAM blocks: devzone.nordicsemi.com/.../
But the current version...
Hi, i use the SDK11 and i will send and receive beacon and be able to launch a BLE DFU.
I am able to make a software in wich i can receive and send BEACON but in...
I'm trying to upload via DFU from one nRF51822 to another nRF51822 via DFU
The receiving side is not a problem as there there are loads of examples.
But I can't find...
Hi,
I'm developing some code for an AVR MCU with the Adafruit nrf8001 and had a question about the expected behavior of the handshaking lines, REQN and RDYN
My understanding...
Hi all,
I'm working on nRF5_SDK_11.0.0_89a8197 using eclipse IDE. If I build any example project it compiles all the files every time even their is no changes in files...
Dear Nordic Team,
Thanks for support.
Last two weeks i am try to BLE DFU example code. But its not work. Please Check this Thread also devzone.nordicsemi.com/.../
...
My GATT service measures a few values, and stores them (~ 100 bytes). When the GATT server (phone) requests data from a specific characteristic, I would like to return the...
Dear Nordic Team,
Thanks for support.
I am using nrf51422 kit and SDK version 11.0. I want to know the BLE DFU test using example codes.
Enclosed bootloader hex file...
