Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
The nRF51 reference manual says that GPIO PIN_CNF registers are retained registers and that "a retained register is a register that will retain its value in system OFF mode...
Hi,
I'm trying to add second service on the fly, while SD running. After adding it, I'm trying to send service changed notification, but it don't work. Below is code used...
Hello.
I test nrf51822 central and peripheral.
I want to change radio channel frequency about nrf51822.
I test source code as below.
nRF51_SDK_10.0.0_dc26b5e\examples...
there is an error on softdevice on src\ll_adv.c on line of 659 . what is the reason?
this is my adv init
#define DEVICE_NAME "navid" /**< Name of device. Will be included...
hi
I want to know whether we require MCU for enabling "Enhanced shock burst mode " or when we set the CE pin to high for making RX that time automatically this will enable...
Hi everyone,
I am using the nRF51822, I have an issue of programming the bootloader.
It is said that the flash is not erased. But I just did an erase all before programming...
Hello,
I have two questions regarding nRF52832 ADC, which are not documented :
what is the precision / tolerance of the internal 0.6V reference?
what is...
hello there,
I use currently 'ble_app_hids_keyboard_s132_spi_pca10040' app of SDK11 for my nrf52832_xxaa device on 'IAR' IDE. It utilizes sofdevise s132. I do not use the...
Hi
I'm encountering a problem in UART communication with nrf51422 on a custom board over an FTDI USB-serial converter ic.
When I send a string > 40 chars from the terminal...
hi
i have nrf51422 sdkv6 ss10 v1
i have timer2 inited
after something like 30 minute that it work right it stop without any system or ble event and it goes here
...
ibeacon noob here, I see several postings about implementing with different chips. Is there a preferred solution for an ibeacon for new designs? Thanks!
So I've been following these blogs on getting Monitor Mode Debugging working with SEGGER Embedded Studio: devzone.nordicsemi.com/.../ and devzone.nordicsemi.com/.../
These...
Hi,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
I try to modify the example code let it can connect to the Blood Pressure (loading...
Hi, I have written some code following an example for my nRF51-DK using a sensor and HeartRateService, but I tried to use some apps and the scan doesn't seem to see my phone...
