I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi, GSMA Database suggests that nRF9160 has 2x IMEI, however I am only able to get one. Pakistan Telecommunication Authority is not allowing me to use the device till I provide...
C:/ncs/v2.9.1/zephyr/include/zephyr/toolchain/gcc.h:87:36: error: static assertion failed: "/soc/peripheral@50000000/uart@c7000 defined without sleep state" ,when i use the...
Hi,
I'm developing an application running on a nRF9151 that connects to AWS. I'm using the aws_iot library and my code is based on the aws_iot sample application. While...
Hi, I have a nRF5340 using hci_ipc that has the following features:
Central Role + Scanning (Multi-connection to nRF52840 peripherals)
Peripheral Role
QoS Channel...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
Description:
I am working on an application using the nRF9160 and encountered an issue where the #MQTTEVT event is not triggered after connecting to an MQTT broker using...
Hey all,
I try to flash the SuperMini nRF52840 using my NRF52-DK over Debug HW (SWDIO pins). I try to flash the Zephyr blinky example.
I think I already got it (at least...
Hello,
I'm developing on a custom nRF5340 board without an external clock source - nRF Connect v.2.9.0. For my application, I'm using the internal system clock with this...
Hello,
I have made a PCB has 4 buttons and touchpad, now I want to drive all of them.
1. one button for left button of mouse. 2. one button for right button of mouse....
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Hi,
I am attempting to get Direct Test Mode working on my nRF54L15 while also having access to the normal BT stack.
Normally, if I run dtm_tr_init(), I can begin the test...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
Hello,
I have a custom nrf5340 board with an attached external RAM on the QSPI (I understand only NOR flash ICs are supported) on the older version of the SDK such as...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
