after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I am trying to use the HCI UART application with channel sounding enabled and communicating with an external host. I was able to perform all CS procedures, and when it was...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
I'm currently developing a USB dongle using the nRF52840 , and I'm facing an issue with inconsistent data reception intervals. I’d appreciate your insights on this problem...
Hi,
Our team is interested in WiFi location service in Cloud Services.
https://www.nordicsemi.com/Products/Cloud-services/Location-Services
However, under the WiFi...
Hi,
I'd like to know how can I implement a Scene Server for one or more Generic Onoff Servers (typically leds).
I read the documentation related to Scene Server and I...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
