Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
Hello,
Recently, my team has been struggling with an issue regarding a nRF5340 device that's encapsulated and inaccessible to be flashed with a JTAG connection. Our normal...
Hi everyone,
I was wondering if there are any issues turning on and off the ANT transmitting channel during run-time of nRF51422 with this:
err_code = sd_ant_channel_close...
I want to use master spi mode ,but when I build the file,it is always error.I operate like this ,First I open the project in ble_peripheral\ble_app_hrs\pca10040\s132\arm5_no_packs...
"Hi Guys, my nRF8001 BLE is working perfectly, But recently i was performing regression testing to check BLE connection, their i faced one issue after 10 minutes from nRF8001...
I am using SDK11 on a nRF52 board. I had some success in DFU, but also had issues.
Was able to upload the bootloader successfully using Master control panel. But it always...
I use the nRF52832 IC of WLCSP package.
In addition, it sets as follows:
{.source = NRF_CLOCK_LF_SRC_RC, \
.rc_ctiv = 16, \
.rc_temp_ctiv = 2, \
.xtal_accuracy...
Hi all,
I have a firmware in which I want to use BLE and ANT communication (with Softdevice S310) to send and receive commands from other Nordic devices or smartphones...
Hi,
I modified the code from the tutorial at devzone.nordicsemi.com/.../ to send measurements from my RHT sensor but encountered some basic difficulties. After fitting...
Hi,
I would like to know what the approximate Flash memory and RAM usage by nRF51 chipset would be when using the BLE communication (Let's say I want to send and receive...
Hi everyone
I am working with nRF52 (SD132). I am considering the ble_app_uart example and I'm trying to modify it by setting TIMER1 and TIMER2 peripherals to generate...
I'm trying to update the bootloader over the air, I succeeded to do so following the answer given here
it worked when I didn't change big things in the bootloader , but...
We have noticed that when our application is trying to call GATT disconnect while nRF master app is running, our app fails to disconnect. More over, when our app connects...
Hello everybody,
I am trying to pair module nRF51822 with Heart Rate Monitor device with the Surface Pro running on Windows 10 with no success. I see the module but when...
This question is a follow-up to this post . After performing several tests and understanding that some phone are more limited than others in terms of the number of exchanged...
Hi,
my device resets on executing sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler);
I have external 32KHZ crystal. I also know that software works because...
