Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi all,
I would like to setup a system where a single central BLE device (a smartphone) has to talk sequentially to several BLE perihperals (Nordic chips).
I need to...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I made timer(repeated) as below.
void init_timer(void)
{
uint32_t err_code;
err_code = app_timer_create(&m_timer_id,
APP_TIMER_MODE_REPEATED...
Hi,
I have a nrf51-DK, and I use softdevice s130_1.0.0 with keil c 5.18a,
My project with custom service uuid "DFU" and custom uuid "my_uuid", and battery uuid, alert...
Hi,
I've noticed that in the examples that come with nRF5 SDK11 there is a template for creating BLE peripherals (ble_app_template). I was wondering if a similar example...
Hi.
I'm using PCA10028, SDK10.0.0, S130 as central.
After connection, if i want to change SUPERVISION_TIMEOUT, is it possible?
If it is, how can i do that?
I need...
Hi.
I am trying to get the RTC started, and I've followed the rtc example in the NRF51_SDK.
But things go wrong when I call:
ret_code_t err_code = nrf_drv_clock_init...
Hello , RX: nrf24LU Tx: nrf51822 use ESB Lib. But the nrf24 Can't receive data continuous.
if I Want receive 2th data , I must power up the nrf24.
This is my Code :
RFCTL...
hello,
I wanted an info which tool is better for debugging when using
native SDK.
do i have to use pyocd or openocd for native sdk hardware debugging
and if you can...
Based SDK 9.0 "ibeacon" example, nRF51822(QFAAG0) work's well when download the ibeacon.hex.
The target set as follow:
Based SDK 9.0 "ibeacon" example,nRF51822(QFABC0...
Anyone seen the new nRF52 online power profiler ?
It's an online tool that estimates the current consumed by your BLE application.
This allows you to better understand...
Hi,
Before starting advertising using advertising_start() function, if pstorage function is used to write data, then it gets stuck at that point as no pstorage handler...
Hello, I have an issue with ble_app_hrs_rscs_relay that doesn't seem to exist with the other sample projects.
The project compiles without any issues, but when I run it...
Apart from pressing Button 4 or adding a DFU service to current running application. Is there any way to enter DFU mode from application?
Is it possible with nrfutil to...
Is there any tutorial or good example for I2C communication using TWI? I already saw the examples for TWI, but I don't find them very intuitive to change for I2C.
I'm trying...