I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello,
If I supply 1.85V on the "External supply" pins, can i use all the modules of the board (nRF51DK)?
I need to have less than 2V on some of the pins as an output...
Our application is a smartband based on nRF 51822 with SDK 9.0 S130, and we found that the device will stop advertising unexpectedly (application is still alive). We have...
Looking at the radio section of the nrf52832 data sheet I see that in section 21.1.2 Packet configuration it is stated that
"For all modes that can be specified in the MODE...
Hi everyone,
Just a brief introduction about my system, I am currently working on Brain computer Interface which was funded by NSF. In our system we have Sense electronics...
hello there , i have put my nrf51 dk in system off mode.then i am generating interrupt using button 3 to wake up it. but my nrf51dk can't wake up. can you hel p me??
my...
Hello.
I use nRF52 DK, S132v2 and PCA10040.
I want to get timestamp like GetTickCount of C++.
When I searched Documentation, I found RTC what can do like GetTickCount...
Hi,
When I finish coding, I can generate .HEX file for all products. But for real mass production, I may need to flash a seperate serial number in somewhere for each PCBA...
I'm trying to transfer a txt file by sending it from a terminal to my NRF52 DK with the BLE_UART example. I always get a BLE_ERROR_NO_TX_PACKETS avter a few packets though...
Hello, everybody. We have a custom board with nRF51288. We also have code based on ble_template that is working on Nordic devboard and dongle. Code is also working on our...
I am having difficulties porting the SPI Master demo to an S130 Soft Device on SDK 11.0.0. From the looks of it, there seem to be some issues with interrupts but I am unsure...
Using S130,
Central device,
Manual whitelist,
custom hardware.
Manual connection to 1 or 2 peripherals depending on a switch position.
This device is a central that...
hello there . i want to do something like when i press button advertisement starts. when i release button advertisement stops. can anyone tell me how to do this?? any sample...
Looking at Table 40 in the nRF51 Series Reference Manual v3.0, the Memory Protection Unit prevents request sources in Code R1 from writing to RAM R0. But if the request source...
I am facing the below issue that no source is available for "0xffffffff" when i try to debug the program using eclipse
I am using softdevice s110 and have flashed the...
