Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
As title, where can I find the syntax for this editor?
If it does not exist,
Q1. How can I put sample source code block?
Q2. How can I put new line only? (without...
Hi,
What's the maximum current for nRF52832 when only CPU is running from RAM at 64MHz (DCDC 3V condition)?
From Product specification v1.0 page 18, does the value "3...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I'm trying to set up DTM environment with my DUT(Own device, using nRF51822) and a nRF51DK for Lower Tester, referencing the document, nAN34_v1.0, "Setting up production test...
Hi ,
I am programming nRF51822(s/n 681859006) on my company's custom board, I am using the softdevice (s110_nrf51_8.0.0_softdevice.hex) to program it.
After successful...
Hi!
I'm compiling with 'GNU Tools ARM Embedded 4.9 2015q2/bin/arm-none-eabi-g++' and optimization -O0 and debug level -g3, nRF5 SDK version is nRF5_SDK_11.0.0_89a8197....
Hi,
I developed an application with nordic NRF51822 using SoftDevice S110 8.0.0.
The APP developer for iOS tells me that the app disconnects after about 2 minutes, while...
Dear all
I have a question about using nRFgo studio to Program Application
I have develop a nRF51422 central project for a few month using nRFgo studio.
The nRFgo...
Hi everyone. I'm using nRF51822 and try to work with Eddystone protocol. I use experimental_ble_app_eddystone and my beacon work properly. I validate it via nrf Master control...
Has anyone else encountered a recent problem while compiling projects using mbed online compiler (error message goes "Struct "" has no field "NRFFW" "RF_UICR->NRFFW[0]" in...
I am trying to implement a OTA DFU in my project. The DFU Examples given create a bootloader file of it's own and starts transmitting in the nrf51422 dev kit(DFU_Targ, ble...
Hello,
Platform nRF52 with SDK 11 (S132)
I use nrf_drv_spi_init to register a Handler (used for screen and SD card so it can be long)
I have sometimes crashes when...
Hello Everyone,
I have deveoped my custom Board using(NRF51) which has four test pins VCC GND SWCLK,SWDIO. I would like to program the custom board. So could anyone tell...
I'm getting the following log messages when I try to initialize the BLE stack:
First from CHECK_RAM_START_ADDR, I get:
RAM START ADDR 0x20002080 should be adjusted to...
Hi,
I want to debug the blinky project on a nRF52 dk (PCA10040) using Eclipse. I strictly followed the instructions as described here: devzone.nordicsemi.com/.../
I...
