Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I use PCA 10040 as a Central, and PCA 10028 as a peripheral. I want the central to connect and pair and bond with the peripheral.
I use S130 for PCA10028, s132 for PCA10040...
I have an application which uses the S132 softdevice and communicates with a DAC over I2C. The twi is in non-blocking mode. Furthermore, there is a significant delay between...
Hi All,
I'm busy exploring the ble_peripheral_uart example and ran into a couple of issues I don't fully understand. Upon flashing the S140 SoftDevice and application program...
Hello All
I am using Soft device 130 and SDK version 12.2.0 ..i am planing to make SPI camera Interface .
I referring SDK online document..there is no any API for slave...
Hello,
Is there any way to disable the "Enhanced Power Control" feature of the BLE standard? I am working with nRF51-DK in the connection mode and I need fixed transmit...
Hi, I am running the ble_app_uart example from nRF5_SDK_ 14.0.0 _3bcc1f7, and found that NRF_LOG_DEBUG () doesn't cause any log output.
Although I have set #define NRF_LOG_ENABLED...
We are running a nRF52832 with SD132.
We are attempting to update the soft device as part of our custom boot loader with the nrf_dfu_mbr_copy_sd.
It returns NRF_ERROR_INTERNAL...
Hi,
I found a bug in the PPI example in the nRF5 SDK v14.0.0 .
In "<SDK_ROOT>/examples/peripheral/ppi/main.c", the following function has an error:
static void timer2_init...
Hi! I'm using nrf52 DK as central and nrf52dk as a peripheral device. Connection interval 10ms. I want to send 10 samples each of 12 bytes every 10ms connection interval....
We know that Nordic have several product lines, some of them are similar or cross functions, is it possible to make a comparison list which maybe list Model / Package/ Flash...
I am trying to build my own application that will be updated via DFU UART.
I can update your given example in
examples/dfu/hci_dfu_send_hex/test_images_dual_bank_update_nrf52...
Hi
When initialising BLE in the softdevice, the following value is used as part of enable_params:-
* @brief BLE GATT initialization parameters.
*/
typedef struct...
Hi
I am running SD 132 2.0.1 on nrf52832 rev 1 and i am getting a chip lock reset occurring. (I have cleared the flags as per the errata and reset pin flag is not present...
....\R2D2_build\R2D2_Firmware.hex: Error: Q0122E: Could not open file '....\R2D2_build\R2D2_Firmware.axf': No such file or directory
keil gave me that error. i did research...
