Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
I want to add wdt function in ble_app_uart. Please tell me where should I feed the wdt.
in below main loop?
for (;;)
{
power_manage();
nrf_drv_wdt_channel_feed(m_channel_id...
I'm trying to decide the best way to be able to have sub millisecond time keeping, but keep the processor sleeping until it gets a hardware interrupt.
Basically I need...
Hello Nordics Developer
I'm from indonesia, i'm electronics designer, i have develop new products using BLE, first develop i'm using nrf51 series but And my boss ask is there...
I'm trying to conserve space in the advertising packet, and would like to free up the space used by the 128 bit (16 byte) service item list, as this takes a minimum of 18...
Hello all,
I am working on nrf51 series for mesh application so regarding Pre addressing of controller how will get to know the adresses of SOC's in mesh network?
can...
I am using the nRF51822 with the s130 softdevice, and I would like to control three RGB LED modules with three PWMs (R, G, and B). For various conditions, either one, two...
[CONDITION]
1. R1 = 1.5M, R2 = 430K
2. GAIN = 1/2
3. RESOLUTION = 10bits
4. Single End
[ISSUE DESCRIPTION]
1. If voltage is changed by 0.1V step (4.1V -> 4.0V), the...
Hello
I wanted to ask what is the correct way to use NRF_LOG_* functions along with printf (with RETARGET_ENABLED 1 ) and normal UART initialized with standard:
const...
Hi all,
I have some problem with the FDS write function.
This is some example codes for my FDS write:
// Global variables
static uint16_t fileID;
static uint16_t...
Hello, I am going over this example here:
infocenter.nordicsemi.com/index.jsp
I am a bit confused how this works. My intention is to create a slave, so a master can send...
Trying to get the BMD-200 board up and running and the blinky_pca10028.hex seems to work just fine but compiling it from source (blinky/pca10028/blank/armgcc)does not. There...
Hi I am using gcc based environment for flashing the nrf52840 SDK with BLE applications. I tried to modify one of the applications to send SPI data received from non-nordic...
I am using sdk12.3 with NRF51822 and the original ANCS project. It can successfully bond with iPhone ,but the bonding only takes place at the first time after the firmware...
