Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
Hi there,
In our device we are using nRF52832 with SoftDevice S112, SDK 17.0.1 and embOS Safe. Up until now we were working with the “Just Works” setting of BLE connection...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Hi All,
I am facing a strange problem. The scenario is that nRF51822 is acting as SPI SLave while MSP430 is acting as SPI Master. Using the SPI slave example as an app...
Hi all,
These steps broke my j-link lite! Is there a way to un-break it? Suggestions welcome.
I updated the segger pc software for another non nRF51 project (using a...
hi, nordic staff.
i'm working at s110(v6.0.0) and s120(v1.0.0). s110 provides notification and indication.
when s120 receives indication value from s110, s120 returns...
Hello all,
I successfully compiled and tested several examples for the nRF51822 Evaluation Kit on my Linux Box using gcc.
To do the same with my Smart Beacon Kit I downloaded...
I am trying DFU to work with gcc and SoftDevice 7.1.
Problem :
MCP able to send the APP binary successfully to the bootloader and DFU bootloader correctly write the app...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi, guys. Now I check the nRF51 IoT SDK(6lowpan, ipv6 over bluetooth).
nRF51 IoT SDK is needed Raspberry Pi, so I make the VMware Player Image for
Ubuntu 14.04.1 LTS 64bit...
I have a nRF51-DK. I would like to control the nRF51-DK through my mobile device.
What is the max. distance which can be reach with BLE(nordic chip)?
Is it possible...
Our application uses the S120 stack, and a bootloader. We want the bootloader to be able to update both our application software and the S120 stack (preserving the MBR). ...
Hi folks,
I have been successful in getting sample code compiled using Keil u-vision and MBED and installing it on nrfDK-51. It has become so simple to install apps - all...
Hi everyone,
I successfully compiled and loaded the experimental_ble_app_uart onto my pca10028 board.
I downloaded and installed the nRF toolbox on my nexus 7 tablet....
Hello everybody,
I want to do something very simple: Read some data from my Bluetooth peripheral. I know the UUID of the data I want to read, but I do not know the handle...
Hmm... this should be a simple question. But I haven't found a direct answer yet in the online SDK docs, the ARM NVIC docs, nor in this forum (and have only been confused...
Hi All,
I have a following setup :
The peripheral BLE device is supposed to send **(time critical )**data packets to Central device but the transfer is very rare (Can...
Hi,
I have modified slightly the OTA bootloader sample in SDK6.1 and SoftDevice 7.1.0. After flashing the bootloader code to the nrf51822 it works like charm, I can update...
