hi support tean,
customer is asking about " Credential storage management %CMNG" in our modem, how to calculate the hash value
i have put the log in below:
[12:33:32...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
Hello, I am trying to develop a bluetooth mesh network with two provisioners, one being an external provisioner (mobile phone) and another being node in the network (nrf5340...
Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
im looking for a developer that can help me work with the NTN functionality of the 3GPP release 17 of the NRF9151-DK so if you are interested please write to me at eric@zerocool...
Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
I'm attempting to take a 115k baud stream of NMEA sentences from a GPS sensor, and outputting it to a phone based on the UART example. While I'm not sure if BLE is perfectly...
Using the ble_app_uart example on the nRF52 PDK, I can easily send multiple packets per connection interval--if I send a long string using ble_nus_string_send(), the notification...
Hi.
I've just received my nRF52840-PDK and now I am trying to run usb examples from SDK 13.1.0.
I have started with VisualGDB using arm-eabi toolchain and USB HID Generic...
Setting interrupt priority according to FreeRTOS documentation is an inverted priority sequencing, i.e. lower number is high priority. However in the freeRTOS example provided...
Hi,
I am seeing an issue where after enabling read back protection (rbp) on NRF52 and using sdk 12.1 the tag goes to state where it drains a lot of current.
command used...
Hello!
I'm using SDK 12.3.0 with nRF51822. Unfortunately since the begining I've got a problem with TWI interface. It keeps crushing my app. For no reason. At the beginning...
Hello,
I am using sdk 12.3.0 and pca10040 board. I want to update the firmware OTA. I am following this post
devzone.nordicsemi.com/.../
I am stuck at step 4)...
I am using the nRF52832 development board, S132 and SDK11.0, I have some questions about Bluetooth pairing,The project under the link：examples\ble_peripheral\ble_app_uart...
when we use twi to transmit data in iic mode ,the nrf52832's power is unacceptable,too high!we read and write data in 50times per second.every time, we transmit 24 byte data...
I JUST NEED TO KNOW NUMBER OF ON PULSES PRESENT IN THE PWM OUTPUT CAN I USE PIN CHANGE INTERRUPT TO COUNT THE NUMBER OF ON PULSES OR SOME OTHER METHOD IS AVAILABLE
Hi,
We need to pass the radio certification and in order to simplify the setup we created an application to setup BLE TX/RX/CC/MC from an NFC command but we meet a strange...
Hello,
As a lot of person, I have a problem for use nrf52832(pca10040 board) with spi as slave.
I check my master with salae probe tool and this part is correct. Chip...
Hello,
my nRF52 Preview dev.kit don't upload the last 2016 march 15 firmware update
from nRFgo app. It gives me always an error and the progress bar stay at 0% value.
...
Hi,
Need you suggestion regarding our use case but first I would like to explain about our use case.
In our use case there be beacons and receiver. Beacon we are considering...
