Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hello everyone,
Currently I'm altering the "ble_app_uart" and "ble_app_uart_c" examples (both under examples/ble_peripheral) to suit my needs. What I currently need to...
Hello,
I have interfaced one sensor with pca10040. I am using sdk 12.2.2. I am sending the data from sensor in advertisement packet(manuf specific data). Now my sensor data...
after the advertising timeout occurs the board goes into sleep mode and then immediately runs from the top of the main function. I know that a pin state change can wake up...
Edit: Rephrased the question to make it easier to answer.
I used flash storage to store a couple of variables between resets in a app made from SDK 12.2, now I am attempting...
hi,
i need to reconfigure the WDT and also change the timer value in WDT. is it possible to do that.
i tried but i can not.
1.configured wdt with timer 5sec.
2.i...
Hi guys,
we are developing firmware for nrf52832 SoC based on the mbed platform.
The firmware uses BLE and few peripherals (timers and pwms). Since our goal is to build...
Is it possible to scan and make Gatt Connection simulataneously from Android app to NRF device.I have seen issues in second connection after disconnection.I have seen second...
Question for I2S.
Execute follow.
[TXD.PTR set A] 1st
[START]
[TXPTRUPD event] (not set TXD.PTR) 2nd.
2nd transfer address use A?
How long time between...
There are a few setting options I would like to keep through power cycle like sensor sampling rate, continuous sampling on/off, etc. I had success implementing saving of one...
I'm using a PCA10056 (NRF52840 Preview DK) v0.9.1, and trying to erase the existing firmware, but running into issues.
I've tried nrfjprog -f NRF52 --eraseall with version...
Hi
I am running some thing similar to the multiprotocol ble_app_gzll example but using freeRTOS and peer manager. Effectively the the main in ble_app_gzll example is a...
In my test, light_control example consumes about 17mA, same for both of client and server.
I'm using nRF52DK, PCA10040, and SDK is "nrf5_SDK_for_Mesh_v0.9.2-Alpha".
I...
Hi,
I am using SDK 12.02 with softdevice 130 and having a odd issue here.
In my application, I want to advertise ADC value via beacon and to report the ADC...
Hello, my
m_device_state
is always NOT
DEVICE_STATE_RUNNING,
so after a little detective work I decided that it's because
provisioner_config_successful_cb...
Hello,
I'm trying to use examples/ble_peripheral/ble_app_uart with SDK-14 and NRF52 DK (pca10040).
The test case is very simple, I use python script to write data to...
