I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello Everyone, I want to use NFC on nrf52 DK to wake up the board from System off. Is there any examples similar to this situation where I can learn more about NFC and Sense...
How should we empty the receiver array after getting response from receiver using uart since previous values are also coming with new values (or) how much delay should be...
Hi,
I'm have compile error that I haven't been able to solve for an nRF51822 on mbed. I'm using this sensor library:
developer.mbed.org/.../
However, it's a bit confusing...
Hi,
I have add the beaconing example to the project, just modify examples.emProject manually. And saw the beacon broadcast "Nordic Semi Mesh" in the lightblue app.
After...
Hi,
I updated all my Packs in Keil for an old project, but now there are a bunch of missing files.
In my build window it says things like:
Error #540: 'NordicSemiconductor...
Hello,
I am using sdk11 on NRF52382 custom Board.
I am trying to save around 1500 words in flash since the page can save approx 1000 words so I change the code to write...
Hi,
I am use nRF51422 and SDK 12.3 sd130.
I can use nRFTool App update FW to nRF51422.
but I dont know how to switch App to bootloader in BLE not button.
which function...
I have doubts about using the pstorage_init function in the example for SDK11 in this answer . Documentation says that this is module initialization routine but in the exemplary...
I combined ble_app_hrs of example with ble_app_hts of example .
I write command in client characteristic configuration,
there is a problem that ATT_ErrorRsp : status...
I have some problem with Interrupt vector,details as below.
I design a bootloader code,and in the bootloader,i use timer0 interrupt.Then in the app code,i use the timer0...
Hi all,
I was wondering if I can install Soft device for a BLE-module other than Nordic?
And if so, will it gonna work?
Thank for help in advance!
blueguy
Hello,
I would like to detect a change in a pin( GPIO_IN_NUMBER ) and depending on it I would like to trigger a SPI transaction, this should happen through PPI.
So far...
I'm trying to migrate my old app based on buttonless app sdk13 to buttonless app sdk14.
I solved issuie according to migrate guide remove chunk things and etc.
My app works...
I am creating an App for iOS using nrf beacon.
App is for garage door and i want to get notification when door closed or open, when beacon is in range or out from range but...
I am using nRF 52840 board. I used Keil 5 to load one of the examples in SDK successfully, but when I unplug the USB cable and used the battery. My program doesn't run properly...
