I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
i am unable to sniff the packets between two devices once the connection is established between two devices..i am using nRF sniffer 1.0 ...
i am able to see only the advertisement...
Hi,
How can I control the PDU error code when reading an attribute.
E.g. Attribbute not found 0x0A. For more info see 3.4.1 Error Handling Bluetooth spec 4.1 Volume 3...
Hi,
I have created a custom PCB that more or less follows the Nordic SmartBeacon design: Beacon_V2.pdf
Instead of BAL-NRF01D3 I used the BALF-NRF01D3 as this is supposed...
I have use random number generator in S110, the source code just like:
uint8_t num_rand_bytes_available;
err_code = sd_rand_application_bytes_available_get(&num_rand_bytes_available...
what does it mean the VTG led turn red ? but it has no bad effect to my project. In addition, I find a strange phenomenon. I use three 1.5v battery to power my board. The...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi nordics!
First of all, thanks for answering my questions before.
Now, I want to generate a clock(48 pulses) with 200us width.
However, sometimes the width of...
Hi ,
I have a application program which uses s110 and UART service .
The issue is the program is not working when I enable the Micro Lib in keil.
On observing the map file...
Hello,
I want to use flash for logging sensor data and sending via BLE.
I found several APIs for store data to flash.
pstorage (Persistent Storage Access Routines...
Hi all,
I would like to know how can I program and debug the nRF51822 development boards?
I've seen some boards have a built-in programmer and others haven't.
How can...
In the DFU code provided by nordic is explicitly states that.
"Soft reset from application must not reinitialize the SoftDevice."
In my application I do not have a button...
Hello,
I have made simple modifications to the multilink central and peripheral examples, adding an additional button and notification characteristic. Things have been...
We're designing a board with the nrf51822 QFA part. Due to design constraints, the chip will have to be about 15mm from where the antenna port will be. The routing to the...
Hello!
I am an electronics engineer in my company, but I'm not familiar with wireless design.
My company will launch a project that will use wireless connection for bidirectional...
