Hello,
I've seen multiple posts related to this question, but they're not very recent so I wanted to check if there's an updated answer.
Are non-simultaneous multi-image...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
Hey guys,
I use SDK 3.0.2 and toolchain 3.0.2 and want to start with the modem shell example: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/modem_shell...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
hi all
i want porting qpc with softdevice. it need set SCB_SYSPRI exception priorities with PRIMASK bit or the BASEPRI register for critical section
can anyone give me...
Hello,
I would like to update an nrf52840 with DFU (usb-serial). On windows I can use nrfutil. But how to proceed if I want to do that from another microcontroller?
Is...
Hi,
I am working with nrf52840 DK and sending real time sensor data to nrf toolbox using ble_uart. I would like to store adc output in flash and then send it over ble uart...
Hi Devzone
I tried to use saadc with 4channels. when I use this without fpu_fft, It prints correct value well.
But, when I insert the fpu_fft and run it, after a while...
Hello
I have a question about SIG certification. As far as I know, to get SIG certified, I need to download the DTM firmware to the board and pass it to the certification...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Dear Community;
I am trying to make an HTTP GET request based on this code . It works fine but I need to adapt that to fit it in my code. I need to pass some arguments...
Hello!
Is there a way to send gps nmea data through ble connection? Almost all gps bluetooth devices use bluetooth classic to send data. The mobile app where I need to get...
Hi,
I need to read the data from the sensor MAXCESS Digital load cell amplifier in which the output we are getting in the form of current ( 4 to 8 mamp) not voltage. can...
Hey guys,
I've been troubled by the this 0x3E issue for almost disappointed to Nordic.
I'm working on a CENTRAL,which is going to connect a headphone with to read some...
Hi i am checking for the Rssi value of the low power node,when i am placing the device in certain feet, it is giving the rssi reading which is approximately matches with others...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
As per below mail I changed settings for...
Dear all,
I'm using an nRF51822 chip for implementing a BLE HID device (mouse) (SDK ver. 12.3.0, SD ver. s130_2.0.1)
I have problems when connecting via BLE with laptops...
Hi..
I want to implement a application ,i want to make a connection one central to multiple peripherals and to transfer the data from the one central to particular peripheral...
