Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
To get the reason for the restart, I called the sd_power_reset_reason_get () function after the ble_stack_init () function in main, but there was a problem. The return value...
Hi,
I'm developing a project which use softdevice and some peripherals together. I want to use serial communication with uart. But i couldn't initialize the app_uart module...
Hi there, Im successfully sending 1.1mB om data from Android Samsung S9 or iPhone 11 Pro. My problem is the low throughput i achieve, its about 6.1kB/s on iPhone and about...
Hi
I have a few questions as a newbee on Nordi products:
Can nRF9160 be used as modem via UART in the same way as i.e. Simcom's ?
Is it possible to run code on the...
nrf_log_push is declared as
I think the const in the parameter should be before the pointer not after it? const-qualifying a parameter (as opposed to the chars pointed...
I am developing a device based on nrf52840, this is peripheral. But I want to change the code so that I can only connect to my device using my application (in other cases...
Hello,
As I am using max30003 ECG with nrf52840 Using NRFX_SPIM example code( SDK15.2-PCA100056 ), I have developed drivers and I am able to read device id through my driver...
We had been using an AT&T M1-enabled SIM in one of our development units successfully for quite some time. After we upgraded that node to MFW v1.1.0, it is no longer able...
I have a custom board based around the nRF9160. I am trying to use the LTE Link Monitor to test the Modem but and having problems.
I am able to connect to my board OK, please...
Hi Nordic teams,
I'm trying to integrate the DFU function into light_switch example this days. At the beginning, I used the dfu example to update my evaluation board, and...
Hi,
Good day!
Statement of problem: In our application, we are using nrf52832 SoC to control critical components (heater). So I was suggested to use a watchdog timer to...
Hi,
Im trying " https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/main.c " gsp example to check supl(AGPS) to integrate into my application...
Hi,
In-app when you scan for device and after it is found you press the connect and then the notification/permission to pair pops out. Our app developers are saying that...
Hi,
We are using nRF51DK for our development, we have developed Android app for Android smart phone.
When the Nordic BLE device advertising we are trying for BLE connection...
