Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
Edit: The problem was caused by me. Solution is in replies.
I was testing read back protection functionality. For one device I've set protection using openOCD by setting...
Hi,
I noticed nrfx_spim.h contains a method called `nrfx_spim_xfer_dcx` but I can't use it directly in my SPIM app.
I am wondering if that method is available to nRF52...
Hello,
I did getting started guide on a new computer (Windows 10 64 bits) and when I tried to check if all is ok with AssetTracker, I got that error message. What cna I...
We are currently getting intermittent errors in our ANT enabled application in field testing. To try to understand where this is happening I want to send over ANT an indication...
Hi ...
I want to measure the temperature using thermistor .. I am working on saadc example . I need give the reference voltage as 5v how to give that ? is there configuration...
We are developping an application using an NRF52840, Based on nRF5 SDK for Thread and Zigbee V3.0.0
Running S140 softdevice
One way of doing OTA is described here (Thread...
Hi,
We need to program nRF5x IC, so for that we are trying to program in the DK boards. For this we are using nRF52840 dk board and nRF51822 dk board (where nRF51822 IC...
Hello.
I try to provision Thingy52 in according with this document.
Can someone help me to create aray byte of invitation please?
In this case we have: Transaction...
Hello,
I wanted to do a rough estimation of max. range between two nRF52840 with ZigBee and BLE with and without coded Phy, for various environments (indoor, outdoor,...
Hello, i intsalled the software stack for use with latest release of nrf sniffer package.
By starting the capture process with wireshark 3.2 i have noticed an issue:
In...
I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
SDK 16.0
nRF 52 DK
LIS3DH Axis sensor
I am trying to understand the sdk_config.h about the NRFX_TWIM_ENABLED config. Here the 'M' stands for Manager or Master? If I...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) In Product specification, it says 2...
