Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I'm trying to understand how the nRF52840 makes RSSI measurements. From what I understand, while other manufacturers implement non-standard RSSI systems, the nRF52840...
Hi,
We are designing a module based on NRF52840 and Li-Po battery. The battery could be charged by a charger module connected to USB.
I have some question regading our...
After having a problems with a function using vsnprintf, I finally boiled it down to sprintf. Every 128 characters that has been run through sprintf, it truncates the output...
I have a BMD-340 eval kit (uses nRF52840) as does my contracted developer who has sent me a hex file to program into my board. I have installed The Segger Embedded Studio...
My configuration:
IAR V8.22
Custom board with nRF52832
Softdevice V6.0.0
SDK 15
I understand that BLE uses, in the link layer, CRC to verify packet integrity...
Hi, has anyone interfaced with the SX1272 using the nRF52840? Perhaps they could point at us some LoRa SDK or libraries which will help the development process?
Thanks
Would a wire-wound inductor work better than a chip inductor for the antenna circuit of NRF52810? I'm using the 32 pin QFN package with the LDO configuration which calls for...
I need to calculate the max number of concurrent connection Central can support given the following
Connection Internval = 7.5ms
Baud Rate per connected peripheral:...
Where can I find this version of hub?
ERROR: Could not find a version that satisfies the requirement hub==2.0 (from -r zephyr/scripts/requirements.txt (line 10)) (from versions...
When nrfutil is installed with python 3, I get an error when generating bootloader settings page. This does not occur with python 2. As python 2 support expires very soon...
Hi.
I am testing MESH by nrf5SDKforMeshv201src and nRF5_SDK_15.0.0_a53641a.
I have a problem.
My project have one of the client and one of the server.
Client transmit...
Hi I had a question to setup the MCP2515 driver in the zephyr project.
We have a custom board for the decawave DWM1001 module, which uses a nRF52832 chip. They have a device...
Hello I am using a I2C sensor module and I need to tranmit only address to receive data back, but I dont know how.
Program crashes on line 4.
Thank you for your help...
I have a DK52 with another device at attached to the SPI bus. I also have a PPK. Should
I connect the second device to VDD_nrf to count as a load? right now it is connected...
