I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi,
We made an online course on Bluetooth Low Energy, includes BLE Fundamentals & Architecture, step by step implementation of Environment Sensing service development...
Hello, I am using nRF9160 PCA10090 DK. I want to make my board as central device and scan for all nearby BLE devices and display its rrsi value and device id on a terminal...
Hi Dears,
I have submit a issue for about two weeks but no response yet, would you please help me for handling it?
The link is https://devzone.nordicsemi.com/f/nordic...
It's really really really annoying that the DevZone contains so much outdated infomations and deadlinks .. especially after moving to the new website !!! :-(
Hello,
I've got a nrf52840 DK and Adafruit nrf52840 Express (less complicated then DK) i'm trying to run a PWM example from datasheet (46 PWM — Pulse width modulation...
Hello Nordic Team
I am working on SDK-v15.3. I have a requirement to update the DFU firmware in lower version too but this SDK version doesn't supporting to update lower...
i am working on a wearable device and want to develop a 1inch wearable using nrf528232 can anyone help e with minimum pcb design requirement for programming.
thanks
I am setting up the DFU example based on NRF52832.
I tried with different version of SDKs (SDK13, SDK15 and SDK16) and all based on armgcc. All toolchains are the same version...
Dear Sir,
I have implemented a program and tested it using BMD-300 Rigado DK.
The program will advertise continuously and I used nRFConnect to connect to the peripheral...
Hi, I would like to capture all bluetooth packets on a specific channel, and get their access code. Same as what Ubertooth does. Is it possible using the nRF52832? If not...
Hi,
I am trying to follow the OpenThread tutorial to build the nRF52840 NCP:
https://codelabs.developers.google.com/codelabs/openthread-hardware/#3
I installed the...
I have successfully completed my bachelor thesis project on a simple wireless sensor network using 3 nRF52 nodes and RPi with using Mqtt and Ble-6LoWPAN example from SDK....
Hi All,
We use nRF52 BLE Sniffer.Its working fiine. Please letus know, weather its possible to sniff multiple BLE devices at a time using single Sniffer. If possible, let...
Will there be an official implementation from nordic of the generic mesh models as described in the mesh model specification or are you counting on each developer to make...
How to change the Bluetooth Mesh broadcast address?
Use the sd_ble_gap_addr_set function to change the broadcast address of PB-GATT ， But PB-ADV still hasn't changed.
...
We are implementing a DFU controller in a microcontroller that communicates with the nRF boot-loader over serial. The target device is nRF52832 using SDKv15.3.0. The boot...
Hello.
I want to see NRF_LOG_DEBUG ("some") through the terminal. When I compile, I get the following error: What should I set or change? MCU : nRF52840 compiler: IAR...
1.I used Nrf52810 and the flash size is 192KB. I now need Master mode and slave mode. The SoftDevice I chose is S132 (S112 slave mode only). I found that S132 (130KB) + Bootloader...
Hi.
I have issue measure ADC value from battery.
setup is NRF52832, SDK 15.3.0, S332, using ANT+, BLE, GPIOTE, PPI, RTC, APPTIMER, LOW_PWM
my goal is measure periodically...
