Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hello,
I am using nrf52 with sdk 12.2.0. I am working with example buttonless dfu template aplication by referring to the link infocenter.nordicsemi.com/index.jsp .
I have...
Hello,
I am running a simple application where I would like to listen for BLE packets for 100ms and then transmit a packet. (no soft device) I can successfully capture...
In section 17.1.9 of the nRF51 reference manual it states:
Maximum consecutive transmission time
is defined as the longest time the
RADIO can be active transmitting...
I need to connect VL53Xl to NRF51 DK> I am using latest 12.2 SDK with Keil MDK.I cannot find any I2C(TWI) example. I can find examples for NRF52 based devices. but not for...
I am using a nRF52832 which act as an observer role only and what is observe it send observed data to another device over UART.
When i turn off scanning and just run UART...
Hi,
I generally use " make flash" (armgcc makefile). If there are multiple devices connected I get a pop-up to select a device/emulator to be flashed. This pop-up just defeats...
Hi there,
I'm trying to use nrfutil generate package with an extern key pair generated with openSSL.
I used opneSLL with prime256v1 curve, which correspond to secp256r1...
Hi,
I use nrf51822 with HF XTAL Frequency of 32 MHz
I am migrating from SDK9 S110 to SDK 12.2 S130 and have a problem that the code stop on nrf_delay_us.
#ifndef...
we wrote a small application to jump to a desired address of our application from bootloader , but UART does not seem to work(i cannot see any transmitted values on terminal...
Hi,
I would like to use the ble_app_hrs to send pressure values via the heart_rate_measurement_send function.
Unfortunately, they are too long: around 105000 Pa (equals...
Hi everyone!
I have an application based on experimental_ble_app_eddystone for nRF52 (SDK12.2), which uses FDS to save in flash memory. Now I want to add the secure_bootloader...
Hello on git hub you add pc-ble-driver
but there is only help how to install it. I did not find any example. And I did not find any documentation how to use it or what is...
Preface: I am developing a software working with different radio protocols (enhanced shockburst, bluetooth,...). Therefore I implemented uart commands for switching radio...
Recently i have purchased nrf51822 and nrf51dk but i dont know how to flash softdevice in nrf51822 using nrf51dk.
please expain me how can i flash or where can i know how...
