Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hello,
currently i am configuring the networking stack on my project.
The goal is to use Matter's built-in Thread connection, to establish a Secure CoAP connection. I...
How should we comprehend the nature of PPI, when dealing with radio interrupts?
For example, if I point radio event handler call back ( of this type:
static nrf_radio_signal_callback_return_param_t...
Hi!
I want to use UART function in my own project, base on ble_app_template.
but when I remove bsp module & board.h, add my custom pin config file, I can't see any UART...
Hi,
I'm attenting the tutorial to use Eclipse + gcc,
when I try to build the blinky project in Eclipse, I have the following error :
17:19:52 **** Build of configuration...
I am following this tutorial to be able to run the ble_connectovity example on the Nordic: github.com/.../pc-ble-driver
I can build and install Boost and cmake runs successfully...
ba_nRF51_spd.zip Hi,
I use nRF51422, SDK10, SD310 and fstorage fun beacuse I need save 10 uint32_t len datas to flash.
I did that....:
the callback fun
static void...
I have a proximity application where I would like to use the nRF51 DK (PCA10028) and Beacon (PCA20006) with Bluetooth Low Energy. I would like them to automatically link when...
Hi,
With the latest SDK (12) there isn't an UART bootloader example available. Am I right?
I'm trying to understand what are the options to program the nRF51 during...
Hello!
nRF52832 IC supports programming OTA the first time after its soldered onto a custom design?
We are designing a very small form factor wearable product and would...
Hello all,
I have a few questions about the best way to go about mass producing nRF51822-based devices.
Can anyone recommend a manufacturer that possesses the...
Cruising through a few questions about the ISP, In System Programming, in the forum and in both the specification sheets, 1.0 and 1.1 there is no clear documentation to the...
Dear Nordic members,
I am currently trying to measure the power consumption of the nRF52832 with the nRF52 DK. I am very new in the evaluation and testing of BLE Chips...
Hi
I am trying to implement long writes on the gatt server side. My implementation is stack handled, so I am going for the " GATTS Queued Writes: Stack handled, one or...
Hello,
As a power source I am using a battery with an open circuit voltage of 3.67V.
The specification states that the recommended absolute maximum supply voltage is 3...
Hello,
I'm trying to make a communication with a nrf51822 and an trf7970a nfc reader. The communication is based on SPI, I read that there are problems with softdevices...
