Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am curious if anyone can point me to an example of working with the SRP functionality in the CryptoCell.
I see the headers for it at nrfxlib/crypto/nrf_cc310_mbedcrypto...
Hi,
I try to create an MQTT AGPS tracker.
I'm using a nrf9160dk with the 1.3.0v.
I use two threads, one for GPS (A-GPS) and one other to send value to MQTT (witch starts...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
To set the transmit power for advertisement, I am using sd_ble_gap_tx_power_set...
We are planing to use nrf52840 sdk in our project.we want to use mesh stack for that.
our product is sensor:
-deployed in oil field.
- send data 8 times a day.
-payload...
Hi,
I'm developing on nRF51422 board and I'm currently adding BLE security just work feature based on SDK12.3.0 using softdevice s130_2.0.1(nRF is used as BLE peripheral...
Hi
Past week (on a Windows 10 pc) I've installed the nrf connect sdk (nrfconnectsetup331ia32), and yesterday offered me an update (nrfconnectsetup340ia32); since I've not...
Hi, I encountered the problem of losing data in uart serial port when using ble_app_uart_pca10040_s132 example.
sdk 16.0.0, s132, 7.0.1, nrf52832,
APP_ADV_DURATION=0,...
I want to connect two nrf52840 device and raspberry pi. When connecting to a single device, it works fine. However, when connecting with two devices, an error occurs and stops...
Hello all,
I am interested in using the Secure Serial Bootloader to program my NRF52832 over UART from an external MCU. I am aware of the SDK example and creating DFU...
I have a system that will have multiple ways of doing DFU. BLE, as normal, UART under special circumstances, and a "no transport" way. In the latter I will have transported...
Hi guys,
I was working on my nRF5340 based custom board. From a certain point on the nRF5340 stopped to accept any command from J-Link (SWD link). For example, in response...
I Separate two projects ,SPM application and non-secure application.the spi driver can work in non-secure application,when I try to transplant the spi driver in SPM application...
Hi,
We are using nRF52840 in HV mode and VDD is configured for 1.8v. By mistake, we have connected VDDH to one of the GPIOs as input. What are the implications? How much...
Hi Team,
We are using nrf9160 DK, So we tested the lte_ble_gateway application where we can take the ble data to cloud acting 9160 as gateway. So we also want to perform...
Hi, I'm trying to get the gps driver to work, but the initialization requires getting a device binding. The Asset Tracker project does it like this:
device_get_binding(CONFIG_GPS_DEV_NAME...
