Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello,
So I assume VDD is from USB or the battery depending on whether USB is there or not. So, when the SAADC outputs ~3.258 V (in low power mode) that's fairly correct...
I need to measure with SAADC two channels in the same time (NRF_SAADC_INPUT_AIN6 and NRF_SAADC_INPUT_AIN4).
Is possible ?
Have you an code example?
Thanks
Marco
Hi,
I used a nRF51 dongle (PCA10031) wit the nRF Connect (v3.3.0) Bluetooth Low Energy application to communicate with a MBN52832 development kit. This works great until...
Hello:
I am looking for the best way to capture the SD and application error/fault(s) so that when the device is restarted, the data can be transmitted to the central...
Hi
I have installed the toolchain according to the getting started assistant, nRF Connect SDK v1.1.0
I try to load the asset tracker application in Segger with CMake_lists...
want to add UART communication to nRF52832 with mesh enable.
I have added,
nrf_drv_uart.c
nrfc_prs.c
nrfc_uart.c
nrfc_uarte.c
files into nRF_Drivers folder...
Hi,
Let's say I have a network with 5 NRF52833-DK and 1 smartphone with the NRFMesh App. How can I achieve to sniff all the ongoing packets in the mesh network on the smartphone...
Hi,
I have a customise board which has nrf52832 chip inside. I want to establish a secure connection between my 2 customised boards but I dont have any button or display...
Hi,
We are currently in development of a custom board with an nRF52840. I'd like to check my IO pin mapping using an IDE if possible, but I was unsure if Nordic or its partners...
Hello. I am using a Nordic Semiconductor Beacon (nRF 51822) and i am trying to connect it to my Raspberry Pi 4, but even though i installed Bluez, scanned using hcitool, i...
Hi,
I have nrf9160 DK. It is ok for ibasis SIM card. But if verizon SIM is used, there is no TCP/IP connection.
I tried to set APN by using:
AT+CGDCONT=1,"IP","vzwinternet...
Hi,
I'm trying to deploy the example program, cifar10, from CMSIS-NN library on NRF52. The issus is I compiled and downloaded it to the board successfully but when I try...
Hi,
I'm trying to combine serial UART functionality into the USBD_BLE_UART example. The goal is to send data in/out to the hardware UART as well.
I started off by loading...
