Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello guys. I have six of these boards nrf52840
Do you have any Arduino Bluetooth sample code for using six or seven of these boards in a peer to peer network setup? ...
Hi , i have implemented a event to flash handler with NRF_SDH_SOC_OBSERVER and it work . But I need to know which operation is related to the event , Es: void FlashEvent_Handler...
I am trying to open HTTPS client project from \v1.2.0\nrf\samples\nrf9160\https_client i am facing below error.
I tried opening different project still i am getting same...
Hi,
I followed this thread ( Link ) to implement a simple message model on the light switch example from nRF SDK for Mesh v1.0.1. I created a "send_simple_message" function...
Hi,
Our custom NRF52840 device uses a cellular modem. We communicate with this modem using AT commands.
We will also be hooking up our devices to a custom server that...
Hello,
I have recently purchased an nrf9160-DK for a project I'm working on here in the UK. Having fired it up and realised that the iBasis coverage is minimal where can...
I'm starting to try to figure out a secure OTA process using the 9160 and tools that Nordic has provided in the SDK and I am confused by one thing I'm encountering.
What...
Hi.
I want to test my iBasis SIM card for NB-IoT with nRF9160DK. So, I tested with the "AT_client" example. I have followed "Getting Start with nRF8160 DK" instruction and...
Hi, I am trying to run ble example - uart in segger embedded studio. I am using 11.0 sdk. I have imported keil project into segger embedded studio. I have the error stating...
Hi devzone,
I'm using translation.
I use nRF52840. I created a firmware like the attached one based on the SDK15.3\examples\peripheral\bie_peripheral\ble_app_blinky. ...
Hi all,
I have a custom board with LED on PIN 11 of nRF52832, and I am using SWD P20 configuration to program my board through nrf52 DK PCA10040. Apparently, nRFgo Studio...
Hi
this is not a question - I'd like to give feedback about the peripheral example usbd_hid_generic.
I'm new to 52840 and new to USB. As learning lesson I tried to build...
Hi All
I am now developing BLE application on nRF52840 DK. I have a question about BLE retransmission process.
When master sends a packet to initiate a connection event...
Hello All,
When I was testing our ble keyboard, there was a problem with the Lenovo tablet connection pairing binding. Please help me, thank you!
1. Ble keyboard is based...
