Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
hi, I used NRF52833 to debug the program, and I used the ble_app_hid_mouse project in SDK16 to debug the fstore function ,and the file path is E:\nrf52833\nRF5SDK160098a08e2...
Hi everyone,
This is my first time using Nordic nRF SDK, so i hope that I'm not asking for anything too stupid, I'm having troubles in adding nrf_logger.h into a project...
I've noticed that the BT-SIG listings for s132 v6.1.x https://launchstudio.bluetooth.com/ListingDetails/64933
and s140 v6.1.x https://launchstudio.bluetooth.com/ListingDetails...
Hello everyone!
We are developing a device with the nRF52840 SoC and using mbed-os for developing firmware.
Everything works and runs normally when using mbed softdevice...
51822+LIS3DH
I have tested my board and got the current consumption value. I use slow advertising only and the interval is 2 seconds. Follow is the result:
1. advertising...
I am using SDK15.0 and added the functionality of nrf_storage into the ble_app_uart in order to store the results of scan (which are kept during run time in an array in RAM...
Hello,
I am use nRF52832 chip in my project.
i am write data in flash by crating record id. For write record in flash I use below code,
For read flash I use below...
we develop 52832 from the project "ble_app_hrs_freertos" , in nRF5_SDK_14.2.0.
occasionally， xQueueSendFromISR returns without pdTRUE in Interrupt handler.
so xQueueSendFromISR...
I designed a custom nrf52 board using the ( nRF52840-CKAA-R ) as the chip. I am trying to program the board using P20 of the nRF52840 development kit and using Kielu5 and...
One of the answers pointed to here www.nordicsemi.com/.../Download , but there is no firmware there unlike the equivalent nrf52 dk page www.nordicsemi.com/.../Download
I found similar questions, but none that were marked as "answered".
I have a working version of "nRF5_SDK_160.0.0_98a08e2/examples/ble_peripheral/ble_app_uart". I also have...
Hi,
I have 3 images that I need to flash on the device (nrf52840 on the nrf9160DK if it matters). They are a trivial boot manager and two application images. I have read...
Hi I plan on using two UART modules from the nRF52840 which is why I am trying to use the app_uart_init however at this stage I keep getting the following error:
undefined...
