Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi All,
I am trying to add custom characteristic to existing HRS profile. I am making few modifications to this profile for my custom requirement.
I am adding new characteristic...
Nordic boards come with the awesome JLINK-OB, and I'd love to use Segger RTT for app tracing, but have been not been able to get it working in Zephyr using the nRF5340-PDK...
Hello,
I checked most tickets on devzone but didn't find the answer for my issue, if you can please help me about this.
I'm using: nRF52832QFAB - SDK16 - SD132 v7.0.1...
Hi,
When upgrading the DFU with an app everythings goes seemingly fine, all init+app bytes received, validated and so on. The DFU does its resets when done updating settings...
Hi,
In our application, we need the TCP/UDP socket keeps alive even when its receiving is timeout. so we changed the process code in do_tcp_receive() and do_udp_recvfrom...
Hi. I am fairly new to all of this. I am currently researching BLE vulnerabilities for a University project. I have had great difficulty attempting to flash the Nordic BLE...
To the kind attention of Nordic support team, I have been putting to the test a scenario where three devices are used: one gzll host and two gzll devices. When devices are...
Hello
I have a project that was developed in Keil, and now I want to migrate it to Segger Embedded Studio. I have followed the tutorial in this link ( https://devzone.nordicsemi...
I'm trying to understand why this happens.
My application uses the softdevice, which configures some NRFFW registers. I program my application, bootloader, SoftDevice via...
Hi
I am using nRF connect for nRF5340 and i am in need to compile using segger embedded studio.
I tried installing segger IDE with the version 4.5 , I got the free license...
Hi,
I encounter a issue with my printed broad that mainly copy the thingy52. I download the thingyv210HW10.hex into my hardware. And then I debug the code (thingysdkv210...
Hello,
Currently, we are working on a product which leverages the following:
NRF52832 (64KB RAM and 512 KB Flash)
SDK v11.0.0
Soft Device 132
It has been reported...
Hi,
I see from the code in GitHub:
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/supl_support.c
That the new A-GPS is using...
Hi! I'm performing buttonless Secure OTA DFU operation on some custom boards of mine. I'm using nRF Connect v3.3.1, and at the moment I'm flashing a zip file containing my...
