I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi,
I have setup the SW project to run run FreeRTOS with BLE stack initialized and nus service started without doing any further BLE use after init in runtime. Sometime...
Hello,
I am using an Adxl362 accelerometer on nrf9160 dk board.
I followed the tutorial a to add the overlay file and even configure the pins i want to use by flashing...
To the kind attention of Nordic support team,
It seems gazell is a very good candidate to be used in tipical working environments, where a bunch (<= 5 devices for example...
Hi,
I am new to Nordic. I bought an NRF52 DK and a Fanstel EV-BT832 development board. As you can see in the picture, both boards are connected to the computer via USB....
Hi,
I had some of your example projects which were being evaluated within Keil and SEGGER and now have an issue with Keil after updating to the PRO license.
I now get...
Hi,
For a peripheral reset, I was recommended to use the code below.
I was just wondering about what the middle line does. Is this a kind of delay to make the reset...
I am trying to start the mesh alongside GATT profiles. I am getting error NRF_ERROR_NO_MEM when calling sd_ble_gap_adv_set_configure in mesh_adv_data_set, which is called...
Hello,
I get the following output when I try to debug the Zephyr's button sample with SEGGER Embedded Studio:
Preparing target for download Executing Reset script TargetInterface...
For the nRF52833:
The product specification is contradictory on the 2 UARTs available. Would you please clarify?
UART0 is this a legacy UART only or does it have Easy...
Our customer has requested access to any test suites the BLE IC vendor can provide which can be used to provide objective evidence of testing & specific test cases.
We started...
I use sdk 15.3.0 / nrf52832 / SD_132.
How to use the prescaler of a timer for an event every 24 hours ?
An example will be very explicit.
Best regards, Jiemde
Hi,
I am trying to evaluate the nrf52840. I am following the instruction to instrument the FreeRTOS from the Nordic SDK15.3. I managed to follow most of the instructions...
Can you update the nRF24L01P EVKIT to add 250K, 1M & 2M data rate selection? Our test house requires we test all 3 rates for the Receiver Blocking tests in EN300328.
1. We are measuring our component performance on nRF5340 PDK and getting pretty high CPU load values. We are suspecting that our code and tables are sitting in flash memory...
Dear All ,
I am a little stumped.... Basically first i was working with the beacon app on sdk 12 on the 51822 chip. Now I have moved to the 52382 chip.
I modified the...
