Hi, I've been given an nRF52 devkit and have been tasked with programming to generate a 2.4GHz signal. The requirement given to me is that simple. (I believe an RF expert...
Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I've managed to find some magic numbers/commands for working with nRF5x devices using the CTRL-AP interface, but having no such luck with the commands on an nRF9160. I've...
To the kind attention of Nordic support team,
I didn't find in SDK16 any SES version of secured usb bootloader for PCA10100 (tell me if I'm wrong). I mainly modified PCA10056...
Hi
Accordingly to Datasheet:
Both the nRF51 mbed interface FW and the J-Link OB image can be downloaded from www.nordicsemi.com.
i have the mbed FW on my Dongle and...
Hi,
I need to add custom information into modem and have found that in v1.2 new ODIS fields were introduced.
As I see I can provide any text for device ID, manufacturer...
Hi Team,
I am using latest Mesh SDK and nRF5 SDK.
In sdk coexist example for nRF52832, I tried adding provision over GATT bearer support instead of ADV bearer. After changing...
Hi to all,
I'm slightly going crazy, I'm looking for information related to LE Audio DEV Kit, all the information brings me to KIT rn52 (ok I'll take it now!) But no one...
Hello, I am building a power switch for my application and have some questions about expected behavior when holding a GPIO output signal at HIGH during System ON sleep mode...
Hello, I tried to merged two examples from SDK
1) I run ble_app_bps example from SDK 15.0 HW - PCA10056, nRF52840
2) I included to the main.c
3) I defined in sdk_condif...
Hello,
I am working on a little app running on nrf5340 app core. Now I want also to program the network core, to be able to exchange data via shared memory as little demo...
IMEI 352656100982084
I need your support to solve this matter urgently because we are developing a IOT solution to monitor several thousand motors - one Thingy 91 for each...
Hi Team,
We are using nRF9160 -DK (0.8.3), As per the document we followed the procedure from here . Loaded the respective application to the on board controller(nRF52840...
Hello
I try to use nrf24l01 in multiceiver mode for a domestic application
I made a simple set-up with 2 nrf24l. On the receiver i activated 4 pipes (0 to 3) with these...
Hi,
I have updated the modem to version 1.2, and connect sdk to 1.2, and now the SUPL library doesn't work? I'm using the GPS sample and it is getting stuck at "starting...
