Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
gaps.zip
Hi,
I have a code that continuously toggles a pin(I use nrf_drv of gpiote+ppi+timer2 for this purpose and interrupt time = 30usec). I have basically taken the...
I know the things like the TWI allow you to send additional data when you instantiate a transacation. Is there any way to do a similar thing with UART?
I'd like to pass...
Hi
I'm using the PeerManager/FDS/FStorage in my project since a few months. We have this software running on real hardware and on simulated environments. While researching...
Hi NORIC's Engineers:
I am a handware engineer who is from Jetway company in China.
I am sorry for my english skill to descripe my questions about NFC antenna of nRF52832...
Hi!
I'm am working on a project where there I need to connect two nrf51 modules and a phone.
Say: Module A, module B and phone P.
The setup i a bit tricky to explain...
I want to use three ADC-inputs on my nRF51832 Engineering Sample B. I read that it is possible to define several ADC-Channels and if a ADC Sample is triggered all Channels...
Hello,
i have a characteristic kept in user space with VLOC_USER. It has read/write with response props and has auth permissions set, both for read and write.
In the...
'morning, I'd like to know how to wire a BMA250 to a nrf52832 please ?
Screenshots : (BMA250) http://prntscr.com/bil9ng
(nrf52832) http://prntscr.com/bil9uu
Thank...
Hi
I've discovered last week some unexpected resets by the watchdog. I guess I've the explanation and the workaround for the behavior, but it would be great to have this...
Hi I am working on activity detection using ADXL362 and nrf52. When I am moving the accelerometer ideally I should get activity interrupt in status register and when ADXL362...
Hi,everyone,
In my project ,I want to save some data when disconnect evt happens; here is my code:
the problem is ths program always stuck in power_manage() function; what...
I'm basing my schematic and antenna design using the PCA10028 as a reference.
I'm not including the J1 RF-connector into my design. Do I still need to include both C6 and...
I only hope that their devices can link their mobile phones, other mobile phone links may not link, but I didn't want to enter a password, directed broadcast method can, about...
I am using the nRF52832 as a MCU in the wearable device,now i want to use the spi master mode to collect data and store data ,and when it is necessary,I want through the bluetooth...
Hi
I have been working with nrf8002 chip. I simply want to program the hardware in a way such that it gives out a signal that can be detected by the emulator.
