I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi all,
I observe a connection supervision timeout (HMI error code 0x08) in my Nordic firmware with certain Android smartphones (controller).
Additional info regarding...
Hi. I'm just wondering if Nordic Semi engineers have done any tests with standard beacons (any particular beacon interval and test condition) application and compared current...
Hi teams,
We made BLE mesh custom boards based on nRF52833.
These nodes are configured to send broadcast messages for every 10 seconds.
Currently, these boards uses...
Hi Sir,
We would like to use the Radio test to do the basick TX/RX test in SDK 15.2
We use the nRF52840-DK for test and follow the CLI document .
1. We use two board...
Baud rate 460800, error code NRFX_ERROR_INTERNAL(1) occurred when the serial port received data。
I want to know how to avoid this problem, the current transfer rate is less...
Hi
We need the recv() be blocking until the full amount of requested data can be returned or the operation was timeout, how to achieve this?
I tried flag MSG_WAITALL but...
Hi. Can anyone think of a way to use the nRF52832 (probably Timer) to detect approximately 125KHz-150KHz variable square wave down to about a 1Hz resolution? I'd like to detect...
Is there any example for Directed Advertising? I'll design my NUS central and peripheral use Directed Advertising, because I would like to have other bluetooth devices connected...
I use this code below mentioned in this question https://devzone.nordicsemi.com/f/nordic-q-a/26030/how-to-reach-nrf52840-uarte-current-supply-specification
This can reduce...
Do you have any recommendations, tutorial, blog, or getting starting guide for a developer wanting to use Mesh and BLE on the same node? Any information would help. Does one...
Hi,
After long use of BLE communication I sometimes get return code 8 from sd_ble_gatts_hvx.
My questions:
1. This return code is cryptic. Is it associated with defined...
I am trying to configure the CryptoCell on an NRF52840 to use AES-CBC encryption with PKCS7 padding. When I call the following function, it returns SASI_AES_ILLEGAL_PADDING_TYPE_ERROR...
Board: nRF52833 DK
Version: 1.0.0 PCA10100
SD: s140
Env: Segger v4.52 (installed on 5/10 via Toolchain Manager)
Hello all...
I'm running into a problem with the...
I have to write this page in case of the application firmware update, so I have to unprotect it in the bootloader (in the nrf_bootloader_app_start_final() function). won't...
We've been hunting down an issue there when we call nrf_drv_uart_uninit() we get a high static current which indicates that a clock or peripheral is being left on.
After...
