Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello
I am preparing for Bluetooth SIG certification. I use nRF52810 / SDK15.0.0 / S112 6.0.0.
I've been helped by Nordic about QDID before.
https://devzone.nordicsemi...
Hi there
After initializing the SoftDevice S132 V6.1.0, I request the HF crystal by calling the function sd_clock_hfclk_request():
Later in the code, after a BLE connection...
SDK:V16.0.0
chip:52832
development kit:window+keil
I trying to combine libuarte and ble_central\ble_app_multilink_central\. My project work well in ble_central. But...
Hello everyone, I need to build a photo capture application.
And the CMOS sensor go through MIPI-CSI2 interface.
Is there any example code and library for nRF5340?
Hi,
How should the USB pins be handled in case I don´t want to use them? Should they be just left unconnected?
What about VBUS pin?
Thanks and regards,
Juan
Hello,
I got the issue to run the NRF9160 DK as an external AT-Modem. What I need to do is to issue AT-Commands over the UART, which control the NRF9160 modem through an...
Hi , I am running zigbee cli example code from sdk and configuring nrf52840 board as coordinator and trying to add xbee module to zigbee network. Coordinator is not accepting...
OK, a bit of confusion somebody can clear up for me, I hope;
Does NRF_SERIAL_EVENT_RX_DATA get sent when there is ANY data in the RX buffer, or only when the RX buffer is...
Hello
I am developing peripheral interfaces on nrf9160 dk, For I2C, sPI and ADC I am not able find exapmle codes. ALso could not find api required for the same to develop...
Dear nordic:
I am working on a tool which can collect data from multiple ant+ sensors with different device types,like a bike computer.
It allows user to assign up to...
I want to communicate with two nRF52 devices without pairing?
It is possible? Yes means kindly give the realtive examples.
Maximum data length...
Thanks.
Hello there, I need to ask if these two; NRF M 24L01+1712AB , NRF M 24L01+1609AH (one with external Antenna) are still supported and have official libraries , and if not supported...
I'm trying to advertise on the coded phy, but SDK 16 seems to have a block in place against doing this when you use S340. I can obviously edit this, but I don't normally edit...
After Installing JLink 6.62 it offered a firmware update for the connected JLink. I performed the update (Firmware: J-Link OB-SAM3U128-V2-NordicSemi compiled Jan 21 2020 17...
