I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I am looking for an updated schematic for the PCA10059 v1.2.0. Everything on info center is version 1.0.0. Noticed that a resistor was added (R7) so wondering if there were...
I'm trying to debug issues in my application related to FDS garbage collection.
My application periodically runs fds_gc() from startup. At this point, garbage collection...
Hi
I got a nrf52833 dk and followed "nrf52833_heart" SDK file readme file is success
next step I install segger studio and JLink_Linux_V662d_x86_64.
wend i open studio...
Hi Devzone:
I saw two functions to write the retention register for DFU, nrf_power_gpregret_set and sd_power_gpregret_set.
What's the diffrence between
nrf_power_gpregret_set...
I'm experimenting with multiprotocol support on a PCA10056 (nRF52840) and the S340 softdevice. I need to use BLE and ANT+ at the same time, sending data to either ANT+ or...
What type of cable is required for the debug out, P19?
The specs for the port only say the number of pins, but not the pitch https://infocenter.nordicsemi.com/topic/ug_nrf52840_dk...
nrf52840 packet transmitting time measurement for TOA or TDOA
Hi I’m cu rrently working with the given nordic project “ nrf52-ble-long-range-demo ”
What I’m trying to...
Hello
Where is the the timeout for the Resolvable Private Address (RPA) defined?
only possible in the central?
can I change the timeout in the android nrfConnect...
Hi,
I am using nRF Connect (Desktop) v3.3.0 with a nRF51 dongle with the latest firmware to test my BLE device application.
My application contains 1 customized service...
Hi all,
My goal is to store large data which is approximately 300KB and send it using UART. To do it, I think I should the library of NVS on zephyr. I achieved to use it...
Hi,
I am trying to make a design for the m odule ISP4520 from ISP, which is basically a pcb with a nRF52832 and a lora radio.
However the processor on the RF52832 is not...
I need to share the LFCLK with an external device and I'm thinking on using an external oscillator like SiT1532AC-J5-DCC-32.768E
I'll set the LFCLKSRC registry as 111 (Apply...
I am setting up a build server that will take care of building our app for the nRF52 and creating the DFU files. For DFU package, I need nrfutil.
Everything is working fine...
The document infocenter.nordicsemi.com/.../nan_040.pdf shows the recommended sizes of the pads (0.275mm) and apertures for the stencil (0.3mm). To connect the inner rows of...
I have some nrf52382 nodes. I want to form two subnet in mesh.
if i using different provisioner to make subnet or something else ？
1. How to Create two subnets: Subnet...
