NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hi ,
1-) Is there any dma half transfer interrupt ? if there is where it is in documents ? ( i check this link but i couldnt see anything about this https://infocenter.nordicsemi...
It is pretty straight-forward to use J-Link RTT Viewer on Windows (as described in the Debugging with Real Time Terminal tutorial ). Is there a similar viewer to use with...
Hi,
I am designing a bio-signal measurement circuit using nrf52832.
I wonder if there is any problem with the performance of nrf52 when using the sensor below.
Sensor1...
I can't comment in https://devzone.nordicsemi.com/f/nordic-q-a/56685/missing-ble_gatts_evt_hvn_tx_complete-events as it is closed but I am also seeing issues with the TX_COMPLETE...
Could you display on the ticket list page also when the ticket was last updated?
Now it shows only creation date, but I do not see indication which one was recently updated...
how can enable the security machanisim for nordic nrf52840
i want to use legacy connection with pass key entry feature
can anyone help me how to start ?
i am using ble_hrs_app...
Hello everyone, I have a network that consists of NRF52840 DK and multiple dongles that are pushing the collected data to central, I would like to retrieve data from this...
https://www.nordicsemi.com/-/media/Software-and-other-downloads/Desktop-software/nRF-command-line-tools/sw/Versions-10-x-x/nRF-Command-Line-Tools_10_6_0_OSX.tar
The file...
Hi,
we have developed a device with the nRF52832 that conncects with an Android smartphone. Our connection is secured and encrypted.
However, that doesn't really prevent...
Hi ,Nordic:
I used thingy:91 boards and firmware verison is thingy91_fw_2019-11-29_d3130d77, The board can connect to the nrf cloud, but cannot obtain gps data. We refer...
Hi
I'm reading the documentation and I have some doubts about the nRF9160 board.
So, the board is divided into the micro controller nRF9160 SiP ( https://infocenter.nordicsemi...
Hi Devzone:
I have 1 differential pair and 1 single ended pin I want to read, so I wrote code below into saadc_init function:
In this case AIN4 is the single ended pin...
Hello Support
When calling the function nrf_nvmc_page_erase(0xF7000) (In nrf_nvmc.c) I immediately get a Hardfault error when the code reaches the line where it calls wait_for_flash_ready...
Hi there,
I'm working on nrf52832 and using a PPI channel between a Timer and an SPI to output a voltage, for now, it works fine. But when I try to make it faster, e.g...
