Hey guys,
I use SDK 3.0.2 and toolchain 3.0.2 and want to start with the modem shell example: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/modem_shell...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
I am following the example guide:
https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-connect-sdk-tutorial
however when I try...
Is there a guarantee that I can do something like: at+cfun=1;+cfun=44
and the nRF9160 will *not* start connecting to a tower? I would like to be able to interface with the...
Hi,
I have searched Devzone for changing the transmission power; even though there were similar issues related to mine but at the end, It did not help me.
I am evaluating...
Hello
I am reading sensor and broadcasting via nrf51DK its working perfectly when voltage supply is morethen 3v
but when I give voltage between 2.1v to 3v its stop broadcasting...
I cannot install the app "Programmer" automatically. The connection always fails due to poor network in our country. The error report is as follows:
Is there anyway to...
Hi Community,
printf() (and variants) fail on rounding floats: This is is probably an error in the printf implementation. I tested it with SDK 16.0 on NRF52840.
Format...
Hi,
In addition to listening the advertiser's and beacon data we also need to offer the master application - which is connected to BLE-module via UART - the possibility...
Questions about ‘Application data’ placement in the flash memory
Is there a function or other mean that could give me what is the lowest flash memory address that is occupied...
Hello All,
I am working on the Nrf52810 with sdk 15.3.
When we connect device through nrf connect app (android) i wanted to disconnect after 1 min .
I have given timer...
nRF52840 DK:
ble_app_blinky is working. After that, I flash ble_app_bms, ( working),
then flash ble_app_blinky- the smart phone is not able to discover service .
Any...
When scanning 1MBPS & Coded PHY at the same time, the probability of Coded PHY broadcast scanning is very low, and 1MBPS PHY broadcast can be scanned normally Slave configuration...
i have come across a couple posts related to providing more compatible Altium design files so that other CAD packages can import them. The best articulation of this point...
Hello I have upgrade software and modem firmware and the program using mqtt protocol don't work any more.
Besides the connection to the broker (many error -106), the program...
Hi, Im using a BMD-300 board with the external crystal installed, I can run zigbee examples fine, even using the external crystal, but when running the Mesh examples I can...
Hi
I have some doubts about NB-IoT and I wanted to clarify them before start deeping developing with nRF91 since this module work with this network.
I know that NB-IoT...
