Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
I would like to modify the way the SPM is built, specifically by setting CONFIG_BOOT_BANNER=n but do not want to modify any files under the ncs directory. I tried the solution...
I have a multi peripheral sample I am trying to make work
I do a
BLE_NUS_DEF(m_nus) and BLE_HRS_DEF(m_hrs)
this will register two event handlers.
When an event occurs...
I have downloaded nRF5_SDK_12.2.0_f012efa and tried to test logging in examples but without success. Even if I compile an example where NRF_LOG_BACKEND_SERIAL_USES_UART 1...
Hi,
I'm trying to use an nRF52840 Dongle to make measurements from 4 SMT172 temperature sensors.
I developed a proof of concept on an nRF52840 DK, where I connect all...
Hi,
Finally i am able to build a basic TCP/IP server client, attaching the project here , i have some questions wrt modem and TCP/IP stack:
I see two different socket...
Hi,
I'm trying to increase Zigbee Tx Power to +8dBm by using the function nrf_802154_tx_power_set().
Digging into the code, I see that it is calling nrf_802154_pib_tx_power_set...
Hi,
I am using NCS 1.2 with Zephyr SMP_SVR example compiling with my own board DTS and using MCUBOOT
I have my own partitions configured in my DTS (attached down at the...
So I'm trying to start off development of my project using the PCA10040 development board. I have downloaded the SDK16 and built a couple of examples no problem using SES...
Hi,
I have a question regarding the frequency of the SPI peripheral of the nrf52.
According to the Product Specification v1.4, the minimum value for the frequency is 125kbps...
Hello Nordic Support!
The stop bit of the last character is short in the Uart output part, and the other MPUy cannot receive the character. How do I fix it until I send...
To the kind attention of Nordic support team,
I was wondering if it is mandatory that Host and Devices share the very same frequency table, with same size.
Is it possible...
Hello,
Because I have no space for additional transistors on my board I made a design with nrF52840 and rgb led connected to 5V.
Configuration o GPIO pins:
H0D1 Value...
I was wondering if I could get some guidance with regards to the effect of interrupting the nRF9160 GPS during an initial cold fix.
Consider an application which uses...
Hi, what is the accuracy of the humidity sensor of the nRF52 at low relative humidity levels (<10%)? Checking if I can trust the numbers I see in a nitrogen glovebag. Thank...
