Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi!
I am trying to send over SAADC data from a peripheral device over BLE to a central device. Currectly I have sucsessfully merged the SAADC and BLE_UART peripheral example...
I'm trying to learn more about automatic current range switch and stumbled across Nordic's nRF6707 power profiler kit that has very interesting topology to choose between...
I have nRF Connect v4.19.2 installed on a Samsung Note 8.0 (Android Tablet)
I have several BBC Micro:bits and I can get their Serial Numbers by three different methods:...
Hello,
We are leveraging the Android BLE Library from Nordic available on GitHub (release v2.1.1).
In a scenario where there are repeated requests to connect as a result...
Hi,
I have an issue about writing and reading data using flash area of nrf9160. I'm using the library of pynrfjprog and the following script for writing/reading data.
...
Hi,
I've used the ADXL362 sensor sample code in the zephyr folder to get the low power accelerometer sensor working on the the thingy91. It triggers on motion and I can...
Hi Nordic Team:
Our important customer develop ANT+ products.They will use zephyr RTOS to develop ANT+ products.But ,they can not find any example project,in the zephyr...
Hi, I want to transfer the firmware to 52832 and enter the bootloader mode successfully. and the I send {0x02,00,00},it can't not enter the case of on_packet_received: SERIAL_DFU_OP_CODE_SET_RECEIPT_NOTIF...
Hi All,
I am developing a data acquisition system in which my device generates an interrupt for every 5ms upon its data is ready. I store one second long data in local buffer...
hi,
We have a product in production but the PCB-A had been updated with new functionality.
We want to make sure old f/w is not inadvertently loaded to new h/w.
To do...
We would like to develop OTA firmware update with nRF52840.
In the development phase, we have been using "Thingy: 91" and place the firmware onto the MCUs of nRF9160 and...
Hi all, I'm developing nRF52832.
My goal is to send ADC data to central device using BLE.
Below is part of my code.
Maximum MTU size is 251.
I sent data in 16...
Hello,
nRF52-DK (PCA10040) has two mysterious 12 pF capacitors C52 and C53 connected to P0.25 and P0.26 respectively (see attached picture).
Is there any special purpose...
I'm using nRF52DK with ble_app_hids_mouse to pair with the smartphone.
From the smartphone we can disconnect the device at will. But I have problem when I want the device...
