Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
I am working on project which is based on nrf9160 Development board.
Where the clock is initialized in example code of thread or GPIO ? Which clock source is used by nrf9160...
Hoping this is a simple fix. I'm new to using GIT and I'd like to setup my nRF 5 SDK projects to work with GIT so I can backup and collaborate with others. I have a few nRF...
Hello
I am interfacing between a SPI Master (microcontroller) with a SPI Slave (nRF52832 based chip) and I get the following output on both ends. The transmission seems...
Hi,
I have run into an issue with nrf52840 on pca10056 v1.0.0 board. The softdevice is SD v6.1.0. It seems to be a hardfault which cause a reset when I tried to call sd_flash_write...
Hello,
I need to read resistive sensors values with SAADC. These sensors going throught multiplexer and amplifier. Infortunaly, the signal going into the SAADC is noisy...
There is a race condition in the SAADC driver when using buffer convert.
I am trying to drive ADC at maximum rate to sample 3 ADC channels, and so I call the following in...
Hello,
after I could not use the nRF9160 DK I bought almost a year ago in Germany due to the missing nb-iot coverage I was very curious about the Thingy91 and I assumed...
Sorry for a noob questions but it is essential at this moment as I have not done any development on NordicSemi chips.
What software and hardware tools I need to develop...
Hi,
I am developing a PC SW that connects to nRF52840 device throw a BLE USB dongle(another nRF52840)
How I can tell from PC that a device is connected\disconnected...
Hi,
I use nRF9160 custom board and my application uses USART, ADC, I2c, SPI, RTC and LTE modem. Currently I am trying to reduce sleep current on IDLE state which is 850...
I am going to use nRF52833 chip with SDK v16.0.0 and SoftDevice s140.
There are couple of questions I would like to clarify:
1. Is AoA/AoD direction finding supported...
Hi
Using the nrf52840-dk with SD S140 and nrfx_gpiote, everything runs fund (BLE, TWI etc) but interrup on pin 0,28 causes a Hard Fault. I can not get any sensible logs...
I am trying to modify the existing Thingy-52 code to have a 'new' characteristic. I used the existing Thingy code to 'clone' a new characteristic (a 2nd microphone channel...
Hi
We tested the idle feature(by AT#XSLEEP=0) on nRF9160DK, but no significant change of power consumption before and after enter into IDLE mode, is this result correct...
Hello, I would like to save a log in the nrf5340 FLASH, how many times is possible to write? May I write in the Application CPU Flash from the Network CPU FLASH when the Application...
