Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello,
I am working on a custom board using a nRF52840 based module. I am using SDK 14.2
I am running the following simple code to sense when an GPIO goes to a low state...
I know I can set the TRACEMUX pins to 0 to enable the GPIO instead of SDO. I do this on the first line of the program.
My problem is that when I click debug, from the time...
hi The serial ports p0.04 and p0.05 on our hardware circuit. We can't communicate with the board with nRFgo studio after modification. The serial port has been closed. Request...
Hello everyone,
In the past few days I have been struggling with the following issue: I have a file on my iPhone, I want to send it to the NRF52840 using BLE (the softdevice...
Hi,
I am running the following setup, both on nRF52840-DK:
1. Central : Always scans , when he finds devices with NUS service -> Initiate a connection
2. Peripheral...
My company has a situation where we have 3+ devices.
A is the provisioner (also an embedded device)
B is a already provisioned device
C is a non-provisioned device...
Hi,
I have made a custom board with u-blox bmd-340-A-R-01 module and trying to erase the flash with PCA10040 DK. I am getting error when I try: nrfjprof -e. Please find...
Serial Example in Mesh SDK allowed embedded system to provision a Mesh network
by interactive_pyaci.py controlling nRF52 with serial example with UART.
But the example...
Hi Nordic
SDK15.2 based application and bootloader running on NRF52840 based UBlox module.
We have the following symptoms happening in the field:
- 2 channels of the...
The customer wants to implement a hid function like the nrf52840 on the nrr9160, and there are no off-the-shelf routines or references to add the hid function.
Hi everyone,
I need your advice regarding the regulator configuration of nRF52840
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840...
Is this the right cable to program the Thingy 91 using nRF9160-DK?
https://www.digikey.com/products/en/cable-assemblies/rectangular-cable-assemblies/450?k=adafruit%201675...
Hi,
I've developed a custom board with nRF5340-QKAA (see schematic sheet attached). nRF5340's VDD pins are not tied to VDDH pin, then I assume the nRF5340 automatically...
I tried to build the OpenThread CLI sample in nrfConnect SDK 3.1 with the version of Segger as installed by the ToolChain Manager. 4.52 on a nRF52840 DK board.
This is the...
Hi I am now aiming to progress ota with android application. Following the guidelines on ithub, I created a class DfuService, NotificationActivity. The class internal code...
